Need help?Do you have a question about the Thermo Scientific Vanquish VH-P10 and is the answer not in the manual?
General| Flow Rate | 0.001 to 10.000 mL/min |
|---|---|
| Pulsation | <1% |
| Flow Rate Accuracy | < 1.0 % at 1 mL/min using 100 % methanol |
| Flow Rate Precision | <0.07% RSD |
| pH Range | 1 to 12 |
Describes the manual's content, structure, and purpose for users.
Explains typographical conventions, safety messages, and notices used in the manual.
Lists additional hardware and software documentation available for reference.
Explains safety symbols and signal words used to convey hazard information.
Specifies the intended use of the pump within the Vanquish system for research.
Provides general and specific safety guidelines for operating the pump.
Covers electrical safety measures to prevent shock and device damage.
Warns about general hazards from substances and biohazards encountered.
Provides instructions on actions to take in emergency situations.
Details recommendations for using compatible solvents and additives for optimal performance.
Outlines compliance with domestic and international EMC and safety standards.
Highlights the main features of the Vanquish pump, such as dual-piston design and seal wash.
Explains the pump's operating principle, including dual-piston design and flow path.
Identifies and describes the user-accessible interior components of the pump.
Details the function and components of the active piston seal wash system.
Explains the function of the purge unit and its connections.
Describes the leak detection system and how it alerts users to leaks.
Explains how to operate the pump, primarily via computer software.
Provides instructions on inspecting packaging, unpacking the pump, and safe handling.
Lists the items included in the pump's delivery package.
Provides safety guidelines specifically for the installation process.
Outlines the steps for installing the pump hardware and software.
Specifies environmental and power requirements for pump installation.
Explains how to open the pump doors to access interior components.
Describes how to set up the pump hardware and its connectors.
Details how to connect the pump to the system via electrical and device connectors.
Provides general rules and recommendations for setting up flow connections safely.
Explains how to route capillaries and tubing using the system's tubing chase.
Provides guidelines and steps for connecting fittings, capillaries, and tubing, including Viper capillaries.
Explains how liquids from the leak tray and purge unit are guided to waste.
Provides instructions on connecting solvent lines between reservoirs and the degasser.
Details setup, liquid choice, and flushing procedures for the seal wash system.
Details how to connect the pump to the autosampler using a capillary.
Provides step-by-step instructions for turning on the pump.
Explains how to configure the pump within the chromatography software.
Introduces the chapter on pump operation and assumes initial setup is complete.
Provides critical safety guidelines to follow during pump operation.
Describes the pump's interface elements like keypad and status indicators.
Details how to control the pump's power using the system base button and main switch.
Provides guidelines for selecting and using solvents and additives for optimal performance.
Details pre-operation steps, including first-time use and sample analysis preparation.
Details parameters like Flow ramps, Leak detection, Pressure limits, etc.
Explains the purpose, items required, and settings for purging the pump.
General guidelines to optimize pump performance, including solvent use and maintenance.
Explains gradient delay volume, dwell volume, and ripple in HPLC systems.
Details how to install optional solvent shut-off valves for flow control.
Instructions for short-term and long-term shutdown of the pump.
Introduces routine maintenance, service, and repair procedures.
Provides essential safety guidelines for performing maintenance and service.
General rules and recommendations for successful maintenance and service procedures.
A suggested maintenance plan with daily and regular tasks.
Procedures for flushing the pump to avoid contamination or remove persistent issues.
Instructions for cleaning and decontaminating the pump, with safety precautions.
Explains software functions for estimating consumable lifetime and scheduling maintenance.
Procedures for testing, replacing lines, and replacing the seal wash detector.
Covers maintenance tasks for the pump head, pistons, and seals.
Procedures for replacing and cleaning inlet and outlet check valves.
Instructions for testing and replacing the inline filter or capillary mixer.
Procedures for testing and replacing static or capillary mixers.
Instructions for emptying, replacing solvent lines, and replacing solvent line filters.
Method to test the pump for leaks after maintenance.
Instructions for replacing blown main power fuses.
Guide on how to update the pump firmware using Chromeleon.
Instructions for removing and installing the pump doors.
Steps to prepare the pump for transport, including shutdown and disconnection.
Step-by-step guide for removing and installing the slide-in module.
General information to help identify and eliminate operational problems.
Explains how messages in the Audit Trail indicate problem severity and types.
Information about common messages in the Chromeleon Audit Trail and their causes.
Steps to locate and resolve leaks detected by the sensor.
How to check pump head compression values for troubleshooting.
Procedure for recalibrating the pump's pressure sensor.
How to test inline filters and static mixers for permeability.
Details the performance specifications of the Vanquish pump.
Lists the physical specifications of the pump, including dimensions and weight.
General information on using authorized replacement parts and components.
Lists the items included in the pump's ship kit.
Details optional accessories available for the Vanquish system.
Lists parts for pump heads, filters, lines, reservoirs, and kits with part numbers.
States CE, cTUVus, WEEE, and FCC compliance declarations for the device.
Explains the function and use of the pump's digital I/O ports for external signals.
To Next Page
