Need help?Do you have a question about the ThermoPro TP-67A and is the answer not in the manual?
General| Brand | ThermoPro |
|---|---|
| Model | TP-67A |
| Category | Weather Station |
| Language | English |
Details the primary unit of the weather station, which receives data.
Describes the external sensor that transmits outdoor data to the base station.
The cable used for charging the device's battery.
Details the information displayed on the LCD screen, including temp, humidity, pressure, and forecast.
Specifies the operational temperature and humidity limits for indoor measurements.
Defines the operational temperature limits for outdoor measurements.
Indicates the acceptable margin of error for temperature readings.
Specifies the acceptable margin of error for humidity readings.
Describes the visual cues for low battery status on both units.
Features the presence of a backlight for the LCD screen.
Details the design for tabletop placement and wall mounting.
Highlights the rain-resistant construction of the outdoor sensor.
Outlines the battery types required for the base station and remote sensor.
The main screen of the base station showing all readings.
Indicates the weather forecast icon on the base station display.
Shows the current outdoor temperature reading.
Shows the current indoor temperature reading.
Button to activate or deactivate the LCD backlight.
Icon indicating the remote sensor's battery status.
Shows the current outdoor humidity reading.
Icon indicating the base station's battery status.
Shows the current indoor humidity reading.
Displays the current barometric pressure reading.
Selection for barometric pressure units (inHg or mb).
Selection for temperature units (°C or °F).
Button to select the current weather condition icon.
A feature for mounting the base station on a wall.
Location for inserting batteries into the base station.
Button to view historical barometric pressure data.
Button to display maximum and minimum recorded values.
Button to cycle through remote sensor channels.
Controls the LCD backlight, which auto-turns off after 15 seconds.
Allows selection of current weather icons for forecasting.
Switches the temperature display unit between Celsius and Fahrenheit.
Switches the barometric pressure unit between inHg and mb.
Displays historical barometric pressure data from the last 12 hours.
Shows and clears the maximum and minimum recorded temperature/humidity.
Cycles through sensor channels or initiates synchronization mode.
Icon showing an upward trend for temperature and humidity.
Icon indicating stable temperature and humidity.
Icon showing a downward trend for temperature and humidity.
The light-emitting diode on the remote sensor.
Button used to reset the remote sensor.
Feature for mounting the remote sensor on a wall.
Port for connecting the charging cable to the remote sensor.
Button to power the remote sensor unit on or off.
Component that measures the ambient humidity.
Component that measures the ambient temperature.
Slider to set the communication channel for the remote sensor.
Instructions for sliding the channel selector to set channels 1, 2, or 3.
Procedure for resetting the remote sensor.
How to turn the remote sensor unit on or off by pressing and holding.
Notes the presence of a built-in rechargeable lithium battery.
Step-by-step guide to fully recharge the remote sensor before use.
Explains the red light during charging and green light upon completion.
Describes the low battery icon appearing on the base station display.
Instruction to replace batteries when the low battery icon appears for the base station.
Instruction to charge the remote sensor when its low battery icon is displayed.
How to change temperature display unit between °C or °F.
How to change barometric pressure unit between inHg or mb.
Steps to place sensor near base, insert batteries, and initiate sync mode.
Instructions for setting the CHANNEL selector on the remote sensor.
How to turn on the remote sensor by pressing the ON/OFF button.
Steps to re-initiate synchronization if it fails.
Procedure for synchronizing additional remote sensors (up to 3).
How to select a channel for permanent display or enable auto-scroll.
Confirms that indoor and outdoor temp/humidity are shown after sync.
Pressing MAX/MIN/CLEAR to show highest indoor/outdoor temp/humidity.
Pressing MAX/MIN/CLEAR again to show lowest indoor/outdoor temp/humidity.
How to clear max/min records by pressing and holding MAX/MIN/Clear.
Icon indicating an increasing trend for temp/humidity.
Icon indicating no change in temp/humidity.
Icon indicating a decreasing trend for temp/humidity.
Pressing HISTORY to show barometric pressure for the past 12 hours.
Graph showing barometric pressure changes over the last 12 hours.
Setting the initial weather condition using the WEATHER button.
Lists the five weather symbols for selection (sunny, cloudy, rainy, snow).
Requires at least 24 hours to acclimatize to local weather conditions.
Notes on forecast accuracy (70%), and warnings against reliance for critical decisions.
The forecast predicts weather for the next 12-24 hours.
Recommendations for placing the base station in a well-ventilated indoor area.
Guidance on placing the remote sensor, ensuring it's within wireless distance.
States that both base station and remote sensor can be wall mounted.
Identifies the model number for additional remote sensors as TX-4.
Provides details on how to order additional sensors from Amazon or ThermoPro.
Steps to try if the receiver cannot connect to the transmitter.
Tips to avoid interference from other electronic devices.
Explains how metal objects like refrigerators can affect transmission.
Warnings against excessive force, shock, dust, temperature, or humidity.
Advises against immersing the unit in water.
Caution against removing any screws from the unit.
Warning that disposing of the unit in fire may cause explosion.
Keeps unit away from children due to choking hazard.
Instruction to dispose of the unit legally and recycle when possible.
Specifies the transmission frequency as 433 MHz.
States the maximum transmit power is 8 mW.
Defines the transmission range up to 330 feet in open area.
Specifies the indoor temperature range as -4°F to 158°F.
Specifies the outdoor temperature range as -31°F to 158°F.
Specifies the humidity range as 10% to 99%.
Indicates temperature tolerance is +/- 2.0°F (+/- 1.1°C).
Specifies humidity tolerance as ±2% from 30-80%, ±3% outside.
Details power source: 2xAAA for base, 18650 lithium for remote.
Instructions for disposing of batteries at approved facilities.
Advice to respect local regulations for disposing of electrical equipment.
States the device must not cause harmful interference and must accept it.
Warns that unauthorized modifications can void user authority.
Notes compliance with Class B limits for residential interference protection.
Suggests measures to correct radio/TV reception interference.
Manufacturer's declaration of compliance with Radio Equipment and EMC Directives.
Provides a link to the complete declaration of conformity online.
Warrants the product free of defects in parts, materials, and workmanship for one year.
Instructions for obtaining repairs or servicing under warranty.
Provides customer service phone numbers for USA, Canada, and UK.
Email address for customer service inquiries.
Specifies the operating hours for customer service.
To Next Page
