What to do if sparking but no flame ignition in Thor Kitchen HRG48?
If there is sparking but no flame ignition in your Thor Kitchen Ranges, the gas shut-off valve may be in the ‘OFF’ position. Turn the shut-off valve to the ‘ON’ position.
What to do if there is a power failure and I want to use my Thor Kitchen HRG48 Ranges cooktop burners?
Yes, the cooktop burners can still be used during a power failure. To light them manually: Hold a lighted match to the flame spreader, push in on the control knob and turn counterclockwise to LITE. When the flame is burning all the way around the burner, you may adjust the heat. Important! If the flame is blown out during a power failure, turn the knob immediately to OFF, as the burner will not automatically relight and gas may escape.
What to do if burner flames are very large and yellow on my Thor Kitchen HRG48 Ranges?
If the burner flames are very large and yellow, it could be due to several reasons: clogged burner bezel ports, burner ports or burner caps not positioned properly, using the wrong type of gas, or a faulty regulator. Try cleaning the burner bezel ring ports with a straightened paper clip, needle, or wire. Also, remove and carefully re-install the burner bezel and caps. Ensure that the type of cooktop matches the natural gas supply. Check the regulator installation, replace the regulator, or set the regulator for the proper gas.
Why do some burners not light or flames don't burn all around the burner cap on my Thor Kitchen Ranges?
This issue may occur if the burner parts or igniters are wet, dirty, or misaligned. Ensure that the burner parts and igniters are clean, dry, and correctly assembled. Refer to the ‘Care and cleaning’ section for instructions.
What to do if there is a power failure and I want to use my Thor Kitchen Ranges oven?
The oven cannot be used until power is restored if there is a power outage in your home or neighborhood.
What to do if my Thor Kitchen HRG48 Ranges burners flame goes out at low setting?
If the burner flame on your Thor Kitchen Ranges goes out at a low setting, there may be low gas supply pressure, or the air intake holes around the knobs may be obstructed. Contact your gas company to check the gas supply pressure and remove any obstructions around the knobs.
Why won't my Thor Kitchen Ranges burners light?
If some of the burners on your Thor Kitchen Ranges won't light, the burner parts or igniters may be wet, dirty, or misaligned. Ensure that the burner parts and igniters are clean, dry, and correctly assembled.
What to do if igniters spark continuously after flame ignition in Thor Kitchen Ranges?
If the igniters in your Thor Kitchen Ranges spark continuously after the flame ignites, the power supply polarity may be reversed, or the igniters may be wet or dirty. Correct the polarity or dry/clean the igniters.
What to do if my Thor Kitchen HRG48 oven will not heat?
Make sure that the oven settings are correct. Follow the mode selection and clock settings as specified in the Oven Operation section of the manual.
How to fix Thor Kitchen HRG48 burners that will not light?
If some burners on your Thor Kitchen Ranges won't light or the flames don't burn all around the burner cap, it's possible the burner parts or igniters are wet, dirty, or misaligned. Ensure the burner parts and igniters are clean, dry, and correctly assembled. Refer to the ‘Care and cleaning’ section for detailed instructions.
General| Fuel Type | Gas |
|---|---|
| Number of Burners | 6 |
| Oven Type | Convection |
| Color | Stainless Steel |
| Width | 48 inches |
| Dimensions (W x D x H) | 48 x 28.5 x 36 inches |
| Weight | 400 lbs |
| Cooktop Surface | Stainless Steel |
| LP Convertible | Yes |
| Total BTU | 90, 000 BTU |
| Ignition System | Electronic |
| Oven BTU | 30, 000 BTU |
| BTU per Burner | 18, 000 BTU (x2), 15, 000 BTU (x2), 12, 000 BTU (x1), 9, 000 BTU (x1) |
To Next Page