Tiger PDU-A40U User Manual

1111
6
Select [Keep Warm]
Press
Temp.Set
key.
■Keep Warm temperature
208
(approx.208°F). 194(approx.194°F).
176
(approx.176°F).158(approx.158°F).
Each press of
Temp.Set
key changes different
temperature setting as shown.
•
You can change temperature setting during Boiling
cycle or Keep Warm.
If the power cord comes off during the
temperature setting, the setting is not completed.
It will go back to default setting. (194)
Caution
■During the boiling cycle
FlashingFlashing
Displaysalternately
approximatelyevery
10seconds
Current water temperature Remaining time until boiling
※
Timing to start displaying remaining time will vary depending on
the amount of water and the water temperature.
※
Water temperature will be displayed by every 9°F. (If it is
approximately 208°F, it will display "208".)
7
Automatically set to warmer
■When boiling
■
When water temperature reaches setting temperature ...
Beeping
sound
•
Do not come in contact with the steam to
avoid being scalded.
•
Do not open or close the lid with excessive
force and do not dispense hot water during
the boiling cycle or immediately after boiling.
Failure to do so may cause scalds due to hot
water splashing or steam being emitted.
Caution
Time table for Boiling and Cooling
3.0L Type 4.0L Type 5.0L Type
Boiling from cold water
Approx.24
minutes
Approx.31
minutes
Approx.41
minutes
From boiling to reach 194
warmer temperature
Approx.
1 hour and
5 minutes
Approx.
1 hour and
5 minutes
Approx.
1 hour and
15 minutes
From boiling to reach 176
warmer temperature
Approx.
2 hour and
25 minutes
Approx.
2 hour and
35 minutes
Approx.
2 hour and
50 minutes
From boiling to reach 158
warmer temperature
Approx.
4 hour and
10 minutes
Approx.
4 hour and
30 minutes
Approx.
4 hour and
55 minutes
※
Under these conditions: full water volume, the water temperature /
room temperature is 73°F, and voltage is normal rated voltage.
※
Guidelines for the time required to reach the 208 warmer temperature
are almost the same as those for boiling from cold water.
To re-boil during the Keep Warm cy-
cle. Press
Re-Boil/Timer
key once.
Guidelines for the time required for re-boiling
when the water is at the full water level
3.0L Type 4.0L Type 5.0L Type
Warmer temperature at 208, 194
Approx.4-8
minutes
Approx.5-9
minutes
Approx.5-10
minutes
Warmer temperature at 176
Approx.9-11
minutes
Approx.10-12
minutes
Approx.13-15
minutes
Warmer temperature at 158
Approx.11-13
minutes
Approx.13-15
minutes
Approx.17-19
minutes
※
Adding water or reattaching the power cord during Boiling cycle,
boiling time may extend.
■To reduce chlorine smell during Keep
Warm cycle.
Press the
Re-Boil/Timer
key twice.
Beeping
sound
Beeping
sound
Flashing
Flashing
Press the key twice.
Re-Boil/Timer
Press
Re-Boil/Timer
key and scroll through the option
until you reach your preferred option cycle.
Re-boil
6hour
timer
7hour
timer
8hour
timer
9hour
timer
10hour
timer
boil+
dechlorinate
Keep
warm
※
Be sure to check the display panel for your preferred cycle. It
uses both
Re-Boil/Timer
key and [Power-Saving Timer]
3
Boiling Water
Light
illuminates
Light
illuminates
Light
turns o
Beeping sound
(repeats 5 times)
Flashing
Beeping
sound
Light
illuminates
Beeping
sound
Flashing
Light
illuminates
Be sure the water level is above Refill water mark.

Tiger PDU-A40U Specifications

General

Brand	Tiger
Model	PDU-A40U
Category	Water Heater
Language	English