Titan Controls Helios 11 User Manual

Helios 11 –240 Volts / 4 Light
Controller Overview
The Helios 11 ‘Classic Series’ lighting controller is specifi cally designed for operation of
high intensity discharge (HID) lighting systems. The controller will run your lights for
any sequence over a 24 hour period by using a 120 Volt relay activation cord set. The
controller can handle up to a maximum of four (4) 1000 watt HID metal halide or high
pressure sodium (HPS) grow lights. The Helios 11 lighting controller provides up to 30
amps of capacity on a standard single phase 240 volt circuit. The Helios 11 is built with
only the highest quality components and will provide the user with years of trouble free
service.
Instructions for Operation
• Please consult with a licensed electrician prior to installation of the Helios 11.
• DO NOT install this controller yourself if you DO NOT fully understand these instructions.
High voltage is dangerous!
• Connect your incoming 240 Volt power to the relay contacts. ( View relay for
wiring information )
• Connect the copper ground wire to the grounding lug. DO not remove incoming green
wire from lug; it is required to have a proper grounding connection for your lighting
controller.
• Securely mount your Helios 11near your enclosure and ballasts but away from any
spray/water/mist, etc.
• Verify that all your wiring connections are tight and that no loose wires are exposed.
• Securely mount your Helios 11near your enclosure and ballasts but away from any
spray/water/mist, etc.
• Plug your lights into the outlets on the right and left side of the controller.
• Plug the relay activation cord set into Apollo Series120 Volt wall timer.
• Make sure that all wires and cables have been properly secured.
• When the relay is activated you will hear a “Clunk” sound.
• Your Helios 11 will now control your lights at the desired settings on your Apollo timer
until the power is defeated.
• Caution: Lamps are hot and should be allowed to cool completely (approximately 15
minutes) before handling.
Warranty Information
• Titan Controls® warrants the original purchase of this product against defects in material and
workmanship under normal use for three (3) years from the date of purchase.
• During the warranty period, Titan Controls® will, at our option, and without charge, repair or
replace this product if the controller or any of its components fail or malfunction.
• All returns or repairs must be accompanied by a Return Merchandise Authorization (RMA)
number prior to any service of the product.
• This warranty is expressly in lieu of all other warranties, expressed or implied, including the
warranties of merchantability and fi tness for use and of all other obligations or liabilities on the
part of the seller.
• This warranty shall not apply to this product or any part thereof which had been damaged by
accident, abuse, misuse, modifi cation, negligence, alteration or misapplication.
• Controllers with serial numbers or date tags that have been removed, altered or obliterated;
broken seals or that show evidence of tampering; mismatched board serial numbers or
nonconforming parts; are excluded from coverage.
• Titan Controls® makes no warranty whatsoever in respect to accessories or parts not supplied
by Titan Controls®.
• Monetary refunds of the warranty will not be given.
• The Buyer assumes all responsibility regarding the use & installation of this controller.
• All warranty service is provided through the factory or an authorized service representative.
• This warranty shall apply only to the United States, including Alaska, Hawaii and territories of the
United States.
• Defective controllers need to be returned with the “proof of purchase” receipt.
• For additional warranty information, contact a Titan Controls® Technical Service Representative
or your Dealer.
• NOTE: Titan Controls® is a controller manufacturer. All sales offerings to the public are done
through a nationwide group of Dealers. No sales offerings will be made directly to the general
public.
Service and Repair Program
• For all service and repairs please contact one of our Technical Service Representatives for a
Return Merchandise Authorization (RMA) number.
• All factory service & repairs will be completed within 48 hours of receipt of controller and after
authorization by customer for repairs.
• Titan Controls® will, at its discretion, repair or replace the controller.
• Factory calibration services are available for all Titan Controls®.
• Returning Units: Please contact your retail store for returns.

Titan Controls Helios 11 Specifications

General

Brand	Titan Controls
Model	Helios 11
Category	Controller
Language	English