Titan TTB674TAS - User Manual

Questions and Answers

B
brittanybrownAug 2, 2025
What to do if the motor of my Titan TTB674TAS is not running?
- J
  Jeffrey DennisAug 2, 2025
  If the motor of your Titan Saw isn't running, there are a few potential causes. First, check the cable, plug, socket, and fuse to ensure there's mains voltage. Second, the undervoltage relay might have been triggered by a temporary power loss, in which case you should switch the device on again. Third, the motor may have overheated. If this is the case, eliminate the cause of the overheating, let it cool down for a few minutes, and then try switching it on again.
N
Nicholas SmithAug 8, 2025
Why does the blade on my Titan TTB674TAS make poor cuts?
- L
  Luis BeckerAug 8, 2025
  If your Titan Saw blade makes poor cuts, it could be due to several reasons. The blade might be dull or dirty, requiring cleaning, sharpening, or replacement. Alternatively, you might be using the wrong type of blade for the cut you're making, so consider replacing it with the proper type. Finally, ensure the blade isn't mounted backward; if it is, remount it correctly.
D
david92Aug 14, 2025
Why is there excess vibration in my Titan TTB674TAS?
- J
  jhudsonAug 14, 2025
  Excessive vibration in your Titan Saw can stem from several issues. The blade might be out of balance, damaged or warped, indicating it needs replacement. Ensure the saw is securely mounted by tightening all hardware. Additionally, check if the work surface is uneven and reposition the saw on a flat surface.
R
Rachael HoffmanAug 20, 2025
What to do if the work piece is touching the back of the Titan TTB674TAS Saw blade and is jumping out?
- M
  Melody ScottAug 20, 2025
  If the work piece is touching the back of the Titan Saw blade and jumping out, several factors could be at play. Make sure you're using the fence. Also, the saw blade might be thicker than the riving knife, or the riving knife isn't being used; in that case, replace the blade or mount the riving knife. A dull blade can also cause this issue, so consider replacing it. Ensure the work piece is kept in place until sawing is finished, and tighten the mitre gauge locking handle if it's loose.
R
rnelsonAug 27, 2025
Why is the bevel adjusting handwheel hard to turn on my Titan TTB674TAS Saw?
- A
  Alisha PearsonAug 27, 2025
  If the bevel adjusting handwheel on your Titan Saw is hard to turn, the gear and screw post inside the cabinet are likely clogged with sawdust. Cleaning the gear and screw post should resolve this issue.

Summary

Product Information and Setup

Your Product Overview

Identifies and describes the table saw components, including safety devices.

Technical Specifications

Details performance data, noise levels, and technical specifications of the saw.

General Safety Instructions

Provides essential safety rules, warnings, and precautions for operating the saw.

Health Advice and Dust Hazards

Information on dust hazards and health risks associated with materials.

Additional Safety Precautions

Covers specific safety rules for table saw operation and accessories.

Risk Reduction: Kickback and Vibration

Guidance on reducing kickback risks and managing vibration exposure.

Health Surveillance

Recommendations for worker health monitoring related to tool use.

Assembly and Preparation Steps

Guides through unpacking, assembly of parts, and preparing the saw for operation.

Detailed Operations and Maintenance

Product Functions and Operations

Explains operation of controls, features, and performing various cutting operations.

Adjustments and Settings

Details how to adjust key settings like bevel stops for precise cutting angles.

Care and Maintenance

Provides instructions for cleaning, lubrication, blade replacement, and general upkeep.

Recycling and Disposal

Explains how to recycle and dispose of the product and its components responsibly.

Troubleshooting Guide

Offers solutions for common operational problems and malfunctions.

Declaration of Conformity

Lists product compliance with relevant European directives and standards.

Titan TTB674TAS Specifications

General

Power Source	Electric
Power Output	1500 W
Blade Diameter	210 mm
Bore Size	30 mm
No Load Speed	5000 rpm
Max. Cut Depth at 45°	45 mm
Bevel Capacity	45°
Dust Extraction Facility	Yes
Weight	12.5 kg
Model No	TTB674TAS
Motor Power	1500 W