Topdon T-Ninja Box User Manual

www.topdon.com
I
FCC Warnning:
Any Changes or modifications not expressly approved by the party responsi-
ble for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. How-
ever, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
Copyright
Copyright © 2021 by TOPDON TECHNOLOGY CO., LTD. All rights reserved.
No part of this publication may be reproduced, stored, or transmitted in any
form without the written permission of the copyright owner.
Trademark
TOPDON is a registered trademark of TOPDON TECHNOLOGY CO., LTD in
China and other countries. All other marks are trademarks or registered trade-
marks of their respective owners.
Disclaimer
The contents of this document are subject to changes without notice due
to continued improvements in design, manufacture, and methodologies.
TOPDON is not liable for the damage or losses due to the use of this docu-
ment.

Topdon T-Ninja Box Specifications

General

Brand	Topdon
Model	T-Ninja Box
Category	Diagnostic Equipment
Language	English

Summary

FCC Warning and Compliance

FCC Compliance Conditions

Device must not cause harmful interference and must accept received interference.

ISED Warning and Compliance

ISED Compliance Conditions

Device must not cause interference and must accept interference.

Safety Information

Safety Grade Definitions

Definitions for Danger, Warning, and Caution safety grades and their implications.

General Safety Precautions

Essential precautions for safe operation and equipment protection.

Packing List

Included Accessories

List of accessories included with the T-Ninja Box for various functions.

Manual Introduction

Target Audience and Conventions

Identifies the manual's audience, typographic conventions, and symbols.

About T-Ninja Box

Product Overview and Components

Visual identification and description of the T-Ninja Box components.

Technical Specifications

Component Part Names and Functions

Details the names and functions of numbered parts of the T-Ninja Box.

Device Operating Specifications

Technical details including voltage, current, operating and storage temperatures.

Power Source

Powering the Device

Explains how to power the T-Ninja Box using adapter or vehicle DLC.

Accessories

Diagnostic and Data Cables

Cables for vehicle connection, data acquisition, and EEPROM reading.

Accessory Details

Bench Mode and MCU Converters

Cables and converters for connecting to ECUs via MCU or bench mode.

EEPROM and Key Adapters

Adapters for EEPROM chip work and Benz key operations.

Additional Accessories

EEPROM and MCU Cables

Converter for EEPROM and cable for MCU connections.

Diagnostics Overview

Common Operations Setup

General procedures for diagnostic functions, including hardware connection setup.

Diagnostic Procedures

Wireless Connection and Common Tasks

Steps for wireless connection and performing common diagnostic tasks.

Key Programming Guide

Detailed steps for programming vehicle keys using the T-Ninja Box.

Key Programming Details

Backup and Generation of Keys

Procedure for backing up current key data and generating new keys.

Key Programming Steps

Key Type Confirmation

Steps to select IMMO type and key operations for programming.

Key Learning and Saving

Steps for key learning, saving key data, and entering file names.

Key Programming Execution

Key Information Backup Confirmation

Confirmation message for successful key data backup.

New Key Generation Process

Process for placing a new key and confirming its type for generation.

Key Programming Completion

Key Generation Success Message

Confirmation of successful dealer key generation and next steps.

Gearbox Programming Introduction

Introduction to gearbox programming function for restoring or writing data.

Gearbox Programming

Gearbox Connection Setup

Guides on connecting the diagnostic tool to the vehicle's gearbox.

Gearbox Data Erasure Procedure

Procedure for erasing gearbox data using the diagnostic tool.

Gearbox Programming Steps

Connecting to Gearbox

Steps to connect to the vehicle's gearbox by selecting EGS System and chassis type.

Erasing Gearbox Data Steps

Procedure for erasing gearbox data by selecting EGS Erasure and downloading.

Gearbox Data Operations

EGS Erasure Confirmation

Confirmation steps for erasing gearbox data successfully.

Engine Programming Introduction

Introduction to engine programming for reading and writing engine data.

Engine Programming

Engine Connection Setup

Guides on connecting the diagnostic tool to the vehicle's engine.

Retrieving Engine Chip ID

Steps to retrieve the chip ID for the engine control unit.

Engine Programming Steps

Engine Brand and Model Selection

Selecting the engine brand and searching for the specific ECU model.

Engine Type Input and Chip Identification

Entering engine type and identifying the corresponding main control chip.

Engine Data Operations

Connecting to Engine and Reading ID

Viewing wiring diagrams, performing connections, and reading chip ID.

Engine Data Backup

EEPROM Data Backup Process

Steps to back up EEPROM data and enter a file name.

Flash Data Backup Process

Procedure for backing up the device's flash data.

Engine Data Restoration

EEPROM Data Restoration Process

Steps to restore EEPROM data from a backup file.

Software Upgrade

Updating Diagnostic Software and App

Process for updating diagnostic software and applications.

Software Upgrade Process

Software Installation and Completion Notes

Details on automatic installation, stopping/resuming, and completion notifications.

Warranty Information

TOPDON One Year Limited Warranty Terms

Details the terms and conditions of the one-year limited warranty.

Warranty Void Conditions

Lists conditions that will void the product's limited warranty.