EasyManua.ls Logo

TorcUP TXU Series - User Manual

TorcUP TXU Series
37 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OPERATION AND MAINTENANCE
MODELS TXU-2, TXU-4, TXU-8, TXU-16, and TXU-32
MANUAL
TXU Series Uniswivel Low Prole
Hydraulic Torque Wrenches
TXU Series
Phone: +1 610-250-5800
Fax: +1 610-250-2700
Toll Free: 1-888-TORCUP-1
Email: sales@torcup.com
Website: www.torcup.com
1025 Conroy Place, Easton, PA. 18040 U.S.A.

Other manuals for TorcUP TXU Series

Preview: Manual
Manual32 pages

Questions and Answers

  • E
    ebrownAug 8, 2025
    Why won't my TorcUP Power Tool pump build up pressure?
    • W
      William RoweAug 8, 2025
      Several factors can prevent your TorcUP Power Tool pump from building pressure. It could be due to a defective relief valve (inspect, adjust, or replace it), an inadequate air supply or hose size (ensure compliance with the pump manual's recommendations), insufficient electric power (verify amperage, voltage, and extension cord size against the manual's requirements), a defective gauge (replace it), low oil level (check and fill the reservoir), or a clogged filter (inspect, clean, or replace it).
  • K
    Kimberly OwensAug 12, 2025
    What to do if my TorcUP Power Tool piston will not advance or retract?
    • M
      Megan FloresAug 13, 2025
      If the piston on your TorcUP Power Tool isn't advancing or retracting, the issue might stem from several causes: * Couplers not securely attached: Check and ensure all coupler connections are properly connected. * Defective coupler: Replace any coupler that is defective. * Defective remote control switch: Replace the switch or control pendant. * Dirt in the direction-control valve: Disassemble the pump and clean the direction-control valve.
  • W
    williamskimberlyAug 17, 2025
    What to do if my TorcUP Power Tool cylinder will not build up pressure?
    • A
      andersonandreaAug 17, 2025
      If your TorcUP Power Tool cylinder isn't building pressure, it could be caused by an internal or end plug seal leak (replace any defective o-rings), sheared retaining screws (replace any broken screws), or a defective coupler (replace any defective coupler).
  • M
    Michelle OsbornAug 21, 2025
    Why is my TorcUP Power Tool piston not retracting?
    • K
      Kyle ChaneyAug 21, 2025
      If the piston on your TorcUP Power Tool is not retracting, check the following: * Hose connections: Ensure the advance on the pump is connected to the advance on the tool and the retract on the pump is connected to the retract on the tool. * Retract hose: Connect the retract hose securely. * Retract pin and/or spring: Replace the broken pin and/or spring.
  • L
    Lauren WeberAug 26, 2025
    How to fix a TorcUP Power Tool ratchet that will not turn?
    • D
      Daniel LaneAug 26, 2025
      If your TorcUP Power Tool ratchet won't turn, it could be due to grease or dirt buildup in the teeth of the ratchet link and drive segment (disassemble the ratchet and clean the teeth) or worn/broken teeth on the ratchet and/or drive segment (replace any worn or damaged parts).
  • A
    Anne MartinezAug 29, 2025
    What causes erratic pressure readings on a TorcUP Power Tool?
    • S
      Sylvia BradyAug 29, 2025
      Erratic pressure readings on your TorcUP Power Tool are likely due to a defective gauge. Replace the gauge to resolve this issue.
  • Z
    Zachary HolmesSep 2, 2025
    Why does my TorcUP Power Tool tighten immediately when turned on?
    • W
      William McdonaldSep 2, 2025
      If your TorcUP Power Tool tightens immediately upon being turned on, the hose connections are likely reversed. Depress the advance button to release the tool, then shut the pump off in the advance position and reverse the hose connection.

TorcUP TXU Series Specifications

General IconGeneral
BrandTorcUP
ModelTXU Series
CategoryPower Tool
LanguageEnglish

Related product manuals