Toro 22615 User Manual (English)

Questions and Answers:

L
lgilmoreAug 17, 2025
How to start a Toro Grinder if the engine does not start?
- L
  Lisa GibbsAug 17, 2025
  If your Toro Grinder's engine doesn't start, there are several possible reasons: * The safety bale may be in the OFF position. Ensure you hold the safety bail against the handle. * If your model has an On/Off switch, it might be in the OFF position. Move the switch to the ON position. * The fuel shutoff valve could be closed. Open the fuel valve. * The choke might be open. Close the choke when starting a cold engine. * The fuel tank could be empty. Fill it with fresh fuel. * The spark plug wire might be loose or disconnected. Check the electrode gap and clean or replace the spark plug.
T
tonya65Aug 19, 2025
How to fix a Toro 22615 when the engine does not start?
- R
  Rachel HarperAug 20, 2025
  If the Toro Grinder engine won't start, several factors could be at play. First, ensure the safety bail is held against the handle. If your model has an On/Off switch, make sure it's in the ON position. Check that the fuel-shutoff valve is open and, if starting a cold engine, close the choke. Also, verify the fuel tank isn't empty and that the spark plug wire is securely connected. Inspect the spark plug for any issues, cleaning or replacing it as necessary.
J
Julie StewartAug 22, 2025
How to prevent the belt from slipping on my Toro Grinder?
- D
  Donna McdonaldAug 23, 2025
  If the belt on your Toro Grinder slips or comes off the pulleys, it's likely due to insufficient belt tension. Adjust the belt tension accordingly. Also, consider reducing the cutting depth.
S
Stacy FosterAug 26, 2025
What to do if the parking brake on my Toro Grinder does not hold?
- S
  Shannon LoweAug 26, 2025
  If the parking brake on your Toro Grinder doesn't hold, it could be either out of adjustment or the brake pads are worn. Try adjusting the parking brake. If that doesn't solve the issue, replace the brake pads.
A
ahallAug 28, 2025
Why does my Toro 22615 Grinder engine run rough?
- W
  William YoungAug 28, 2025
  If the engine of your Toro Grinder runs rough, consider these potential causes: * The choke may be left on. Open the choke. * The air filter might be clogged. Clean or replace the air filter. * The fuel line could be clogged. Clean the sediment cup. * There might be water or contaminants in the fuel. Drain and fill the tank with fresh fuel. * The spark plugs may be worn or have buildup on the electrodes. Check the electrode gap and clean or replace the spark plug.
D
Deborah BowmanAug 30, 2025
What to do if the cutting wheel continues to rotate on my Toro 22615?
- N
  Nicholas SmithAug 30, 2025
  If the cutting wheel of your Toro Grinder continues to rotate, it could be due to: * Excessive engine speed. Move the throttle to the DISENGAGED position. * The belt being off the pulleys or broken. Replace the drive belt. * Weak or broken clutch springs. Replace the clutch.
M
Michael SandovalSep 2, 2025
Why is the cutting wheel not rotating on my Toro 22615 Grinder?
- J
  Jill PenaSep 2, 2025
  If the cutting wheel of your Toro Grinder does not rotate, it could be due to: * Insufficient engine speed to activate the centrifugal clutch. Move the throttle to the ENGAGED position. * Insufficient belt tension. Adjust the belt tension. * Worn clutch shoes. Replace the clutch.
S
Sarah BoydSep 5, 2025
How to fix a Toro Grinder when the belt slips or comes off the pulleys?
- S
  Samantha AllenSep 5, 2025
  If the belt slips or comes off the pulleys on your Toro Grinder, it's likely due to insufficient belt tension. To address this, adjust the belt tension and reduce the cutting depth.
E
Eric FitzgeraldSep 8, 2025
What to do if the parking brake does not hold on my Toro 22615?
- M
  mary01Sep 8, 2025
  If the parking brake on your Toro Grinder does not hold, it could be because the parking brake is out of adjustment, so you should adjust the parking brake. Alternatively, the brake pads may be worn, requiring you to replace the brake.
L
Lauren ColemanSep 12, 2025
What to do if the cutting wheel on my Toro 22615 Grinder does not rotate?
- J
  John DaviesSep 12, 2025
  If the cutting wheel on your Toro Grinder isn't rotating, it could be due to a few reasons. First, make sure the throttle is in the ENGAGED position to provide sufficient engine speed to activate the centrifugal clutch. Check the belt tension and adjust if necessary. Lastly, if the clutch shoes are worn, they will need to be replaced.