Toro 75951 - User Manual

80 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

FormNo.3424-649RevC

ZMaster

®

Professional5000or

6000SeriesRidingMower

with48in,52in,60in,or72inTURBOFORCE

®

Mower

ModelNo.74904—SerialNo.403247209andUp

ModelNo.74906—SerialNo.403247600andUp

ModelNo.74918—SerialNo.403227053andUp

ModelNo.74926—SerialNo.403005770andUp

ModelNo.74928—SerialNo.403247229andUp

ModelNo.74930—SerialNo.403319739andUp

ModelNo.74943—SerialNo.403011067andUp

ModelNo.74945—SerialNo.403226784andUp

ModelNo.75951—SerialNo.403319953andUp

ModelNo.75955—SerialNo.404971756andUp

ModelNo.78926—SerialNo.403137993andUp

ModelNo.78928—SerialNo.402320000andUp

Registeratwww.Toro.com.

OriginalInstructions(EN)

*3424-649*

Table of Contents

Questions and Answers

W
William HallSep 22, 2025
What does it mean when the Malfunction Indicator Light (MIL) comes on in my Toro Lawn Mower?
- H
  hfranklinSep 23, 2025
  If the Malfunction Indicator Light (MIL) comes on in your Toro Lawn Mower, consider the following: * Turn the engine off and let it cool if the engine is too hot. * Use new gas if there is old gas in the gas tank. * Open the fuel shutoff valve completely if it is not fully open. * Ensure that the air cleaner and precleaner are clean; replace if necessary. * Charge or replace the battery if it is not charged. * Ensure a good 12 volt battery is being used and is fully charged if the battery voltage is low. * Check and replace any blown fuses.
C
Charlotte LopezSep 15, 2025
Why Toro 75951 Lawn Mower vibrates abnormally?
- B
  Bradley ShahSep 15, 2025
  Abnormal vibration in your Toro Lawn Mower could be due to several reasons: * Bent or unbalanced cutting blades require replacement with new ones. * A loose blade mounting bolt needs tightening. * Loose engine mounting bolts should also be tightened. * Check and tighten any loose engine pulley, idler pulley, or blade pulley. For a damaged engine pulley, bent blade spindle, or loose/worn motor mount, it is recommended to contact an Authorized Service Dealer.
T
tkellySep 13, 2025
Why does my Toro 75951 Lawn Mower machine not drive?
- J
  Joy QuinnSep 13, 2025
  If your Toro Lawn Mower isn't driving, first check that the bypass valves are closed tight and tighten them if necessary. Also, inspect the pump belt for wear, looseness, or breakage and change the belt if needed. Ensure the pump belt is properly on the pulley. A broken or missing idler spring could also be the problem; replace the spring. Finally, check the hydraulic fluid level and temperature; add hydraulic fluid to the reservoirs or let it cool down.
J
Joe ZamoraAug 31, 2025
Why Toro 75951 Lawn Mower engine loses power?
- R
  Rodney NorrisAug 31, 2025
  If your Toro Lawn Mower engine is losing power, consider these potential causes. First, the engine load might be excessive, so reduce the ground speed. A dirty air cleaner can also cause power loss, so clean the air-cleaner element. Additionally, check the oil level in the crankcase and add oil if it's low. Finally, ensure the cooling fins and air passages above the engine are free from obstructions.
A
Audrey ChavezAug 31, 2025
Why Toro 75951 Lawn Mower machine does not drive?
- K
  Kathryn CollinsAug 31, 2025
  If your Toro Lawn Mower isn't driving, start by checking that the bypass valves are closed tight. Inspect the pump belt for wear, looseness, or breakage, and change the belt if needed. Also, ensure the pump belt is properly on the pulley. If the idler spring is broken or missing, replace it. Finally, check the hydraulic-fluid level and add fluid to the reservoirs if it's low, or let it cool down if it's too hot.
R
Robyn WilliamsAug 31, 2025
Why does my Toro Lawn Mower produce an uneven cutting height?
- P
  Philip HunterSep 1, 2025
  An uneven cutting height with your Toro Lawn Mower can be caused by several factors. The blades might not be sharp, so sharpen them. Bent cutting blades can also cause this issue, so install new ones if necessary. Ensure the mower deck is level from side-to-side and front-to-rear. Clean the underside of the mower, as dirt buildup can interfere with cutting height. Adjust the tire pressure to the correct level. For a bent blade spindle, contact an Authorized Service Dealer.
D
Dylan NealSep 1, 2025
What to do if my Toro Lawn Mower produces an uneven cutting height?
- R
  Richard JenkinsSep 1, 2025
  An uneven cutting height with your Toro Lawn Mower can result from dull or bent blades; sharpen the blade(s) or install new cutting blade(s). Also, the mower deck might not be level; level the mower deck from side-to-side and front-to-rear. A dirty mower underside can also cause this issue; clean the underside of the mower. Incorrect tire pressure could also be the cause; adjust the tire pressure.
R
Ronnie DixonDec 1, 2025
What to do if my Toro Lawn Mower engine does not start or keeps stopping?
- R
  Ray LiDec 1, 2025
  If your Toro Lawn Mower engine is not starting, starts with difficulty, or fails to keep running, begin by checking the fuel tank to ensure it's full and that the fuel-shutoff valve is open. Verify the oil level in the crankcase and add oil if it's low. Make sure the throttle control is positioned midway between the SLOW and FAST settings. If these steps don't resolve the issue, inspect the fuel filter for dirt and replace it if needed. Other potential causes include a dirty air cleaner (clean or replace the element), a malfunctioning seat switch (check the indicator and replace the seat if necessary), or corroded/loose/damaged electrical connections (clean and reconnect). Also, check the spark plug for fouling or improper gapping, adjusting or replacing it as necessary, and ensure the spa...
A
Anita MathewsSep 18, 2025
What causes the clutch on my Toro 75951 to not engage?
- I
  Ian HermanSep 18, 2025
  If the clutch on your Toro Lawn Mower won't engage, start by checking if the fuse is blown and replace it if necessary. Check the coil resistance, battery charge, charging system, and wiring connections. Also, look for low voltage supply at the clutch, and check the coil resistance, battery charge, charging system, and wiring connections. If the coil is damaged, replace the clutch. Check for inadequate current supply and repair or replace the clutch lead wire or electrical system, cleaning connector contacts. Finally, if the rotor/armature airgap is too large, remove a shim or replace the clutch.
D
Debra AdkinsSep 15, 2025
What to do if the blades don't rotate on my Toro 75951 Lawn Mower?
- M
  marksullivanSep 15, 2025
  If the blades on your Toro Lawn Mower do not rotate, install a new deck belt, install the mower deck pulley and check the idler pulley, idler arm, and spring for correct position and function, check the belt tension or install a new belt, or replace the spring.

Toro 75951 Specifications

General

Model	75951
Engine Displacement	163 cc
Engine	Briggs & Stratton
Cutting Width	56 cm
Weight	38.1 kg
Start Type	Pull Start
Drive Type	Self-Propelled
Drive System	Rear-Wheel Drive
Fuel Tank Capacity	0.95 L
Cutting Height	1.25 - 3.75 inches
Warranty	2 Years

Related product manuals

Preview: Toro 75967

Preview: Toro 75969TE

Preview: Toro 75304