How to fix a starter that won't crank on my Toro 75967?
If the starter on your Toro Lawn Mower won't crank, check these items: * Ensure the blade-control switch is disengaged. * Engage the parking brake. * Move the motion-control levers to the NEUTRAL-LOCK position. * Make sure you are sitting in the operator’s seat. * Charge the battery if it's dead. * Check the electrical connections for good contact. * Replace the fuse if it's blown.
Why won't my Toro Lawn Mower engine start?
If your Toro Lawn Mower engine won't start, starts hard, or fails to keep running, try the following: * Fill the fuel tank. * Open the fuel shutoff valve. * Add oil to the crankcase. * Ensure that the throttle control is midway between the 'SLOW' and 'FAST' positions. * Replace the fuel filter. * Clean or replace the air cleaner element. * Check the seat switch indicator; replace the seat if needed. * Check the electrical connections for good contact; clean the connector terminals thoroughly with electrical contact cleaner, apply dielectric grease, and reconnect. * Clean, adjust, or replace the spark plug. * Check the spark plug wire connection.
How to fix a Toro 75967 when the starter does not crank?
If the starter on your Toro Lawn Mower doesn't crank, here are some things to check: 1. Move the blade control switch (PTO) to disengaged. 2. Set the parking brake. 3. Ensure that the drive levers are in the neutral lock position. 4. Sit on the seat. 5. Charge the battery. 6. Check the electrical connections for good contact. 7. Replace the fuse.
What to do if my Toro 75967 Lawn Mower machine vibrates abnormally?
If your Toro Lawn Mower is vibrating abnormally, it could be due to: * Bent or unbalanced cutting blade(s); install new cutting blade(s). * A loose blade mounting bolt; tighten the blade mounting bolt. * Loose engine mounting bolts; tighten the engine mounting bolts. * A loose engine pulley, idler pulley, or blade pulley; tighten the appropriate pulley.
What to do if my Toro 75967 Lawn Mower clutch does not engage?
If the clutch on your Toro Lawn Mower doesn't engage, it could be due to a blown fuse, low voltage supply at the clutch, a damaged coil, inadequate current supply, or a rotor/armature air gap that is too large. To address this, replace the fuse, check the coil resistance, battery charge, charging system, and wiring connections, and replace components if necessary; repair or replace the clutch lead wire or electrical system and clean the connector contacts; remove the shim or replace the clutch.
How to fix an uneven cutting height on my Toro 75967 Lawn Mower?
To fix an uneven cutting height on your Toro Lawn Mower, start by sharpening any dull blades or replacing bent ones. Next, level the mower deck from side-to-side and front-to-rear. Clean the underside of the mower deck. Also, ensure the tire pressure is correct. If the blade spindle is bent, contact an Authorized Service Dealer.
How to fix uneven cutting height on Toro Lawn Mower?
To fix an uneven cutting height on your Toro Lawn Mower, start by sharpening any dull blades or installing new ones if bent. Ensure the mower deck is level from side-to-side and front-to-rear. Clean the underside of the mower deck, adjust the tire pressure to the correct level. For a bent blade spindle, contact an Authorized Service Dealer.
What causes the blades to not rotate on my Toro 75967 Lawn Mower?
If the blades on your Toro Lawn Mower do not rotate, it could be due to a damaged, worn, loose, or broken mower deck belt; install a new deck belt. Ensure the mower deck belt is properly installed on the deck pulley, checking the idler pulley, idler arm, and spring for correct position and function. Also, a worn, loose, or broken pump drive belt can cause this issue, so check the belt tension or install a new belt. Finally, check the idler spring and replace it if it is broken or missing.
What causes abnormal vibrations in my Toro Lawn Mower?
If your Toro Lawn Mower vibrates abnormally, try the following: 1. Install new cutting blade(s). 2. Tighten the blade mounting bolt. 3. Tighten the engine mounting bolts. 4. Tighten the appropriate pulley.
Why Toro 75967 Lawn Mower blades do not rotate?
If the blades on your Toro Lawn Mower aren't rotating, it could be due to a worn, loose, or broken mower deck belt; in this case, install a new deck belt. Another possibility is that the mower deck belt is off the pulley; reinstall it and check the idler pulley, idler arm, and spring for correct position and function. Also, check the pump drive belt for wear, looseness, or breakage, and adjust the belt tension or install a new belt. Finally, inspect the idler spring and replace it if it's broken or missing.
General| Model | 75967 |
|---|---|
| Deck Material | Steel |
| Start Type | Recoil |
| Mulching Capability | Yes |
| Bagging Capability | Yes |
| Side Discharge Capability | Yes |
| Cutting Width | 22 inches |
| Drive System | Personal Pace |
| Fuel Capacity | 0.33 gallons |
| Cutting Height | 1.0 - 4.0" / 2.5 - 10.2 cm |
To Next Page
