Toro TimeCutter 74760

Questions and Answers

C
colemanmichelleAug 5, 2025
Why does my Toro TimeCutter 74760 engine not start, start hard, or fail to keep running?
- C
  Cristina FritzAug 5, 2025
  Several factors can cause this issue. The fuel tank might be empty, so refill it. The air cleaner could be dirty, requiring cleaning or replacement. Check if the spark plug wire(s) is loose or disconnected and install the wire(s) on the spark plug. A spark plug(s) may be pitted, fouled, or have an incorrect gap, so install a new, correctly gapped spark plug(s). The fuel filter may be dirty, so replace it. The oil level in the crankcase might be low, so add oil to the crankcase. Finally, ensure that you are using the correct fuel type; if not, drain the tank and replace the fuel with the proper type.
J
Jonathan AndersonAug 9, 2025
Why is my Toro TimeCutter 74760 cutting height uneven?
- C
  carlsonbarbaraAug 9, 2025
  An uneven cutting height on your Toro Lawn Mower can be due to several reasons. The blade(s) may not be sharp, so sharpen the blade(s). A cutting blade(s) may be bent, so install a new cutting blade(s). The mower might not be level, so level the mower from side-to-side and front-to-rear. An anti-scalp wheel may not be set correctly, so adjust the anti-scalp wheel height. The underside of the mower could be dirty, so clean it. Finally, the tire pressure might be incorrect, so adjust the tire pressure.
J
Jordan YoungAug 13, 2025
What to do if the blades do not rotate on my Toro Lawn Mower?
- C
  Carol WagnerAug 13, 2025
  If the blades on your Toro Lawn Mower aren't rotating, it could be due to a worn, loose, or broken drive belt, so install a new drive belt. Alternatively, the drive belt might be off the pulley, so install the drive belt and check the adjusting shafts and belt guides for the correct position. Also, the mower belt could be worn, loose, or broken, so install a new mower belt.
E
ericapetersonAug 17, 2025
Why is my Toro TimeCutter 74760 engine losing power?
- M
  Michael HernandezAug 17, 2025
  A loss of power in your Toro Lawn Mower engine can stem from several causes: excessive engine load, which can be resolved by reducing ground speed; a dirty air cleaner, which requires cleaning; or a low oil level in the crankcase, necessitating the addition of oil. Furthermore, check for obstructions in the cooling fins and air passages under the engine blower housing and remove them if present. Ensure the spark plug(s) is in good condition; if pitted, fouled, or incorrectly gapped, replace it. Check the fuel filter for dirt and replace if necessary. Finally, if you are using incorrect fuel, drain the tank and replace it with the proper type.
S
sarah92Aug 22, 2025
What to do if my Toro TimeCutter 74760 Lawn Mower engine overheats?
- B
  Barbara PayneAug 22, 2025
  If your Toro Lawn Mower engine is overheating, several factors could be the cause. First, the engine load might be excessive, so reduce the ground speed. Second, the oil level in the crankcase might be low, so add oil to the crankcase. Third, check the cooling fins and air passages under the engine blower housing for obstructions and remove them. Fourth, a dirty air cleaner can cause overheating, so clean or replace the air-cleaner element.
P
Patrick MuellerAug 27, 2025
What to do if my Toro TimeCutter 74760 Lawn Mower starter does not crank?
- J
  joshua60Aug 27, 2025
  If the starter on your Toro Lawn Mower isn't cranking, here are a few things to check: Ensure the blade-control switch is disengaged. Make sure the motion-control levers are in the PARK position. Verify the battery isn't dead by charging it. Inspect the electrical connections for corrosion or looseness, and ensure they have good contact. Check for a blown fuse and replace it if necessary.
S
Susan PorterAug 31, 2025
What to do if my Toro TimeCutter 74760 Lawn Mower has an abnormal vibration?
- C
  Christopher LoveAug 31, 2025
  If your Toro Lawn Mower is vibrating excessively, check the following: Tighten any loose engine-mounting bolts. Ensure the engine pulley, idler pulley, or blade pulley is tightened appropriately. If the cutting blade(s) is bent or unbalanced, install a new cutting blade(s). Also, tighten any loose blade-mounting bolts.

Summary

Safety

General Safety

Provides essential safety guidelines for operating the lawn mower, emphasizing operator responsibility and safe practices.

Slope Indicator

Safety and Instructional Decals

Product Overview

Controls

Explains the various controls of the machine and their functions.

Control Panel

Operation Preparation

Before Operation

Outlines essential checks and preparations before operating the machine.

Before Operation Safety

Details crucial safety measures to be taken before starting operation.

Fuel Safety

Fueling Procedures

Recommended Fuel

Machine Break-in and Daily Checks

Performing Daily Maintenance

Outlines the maintenance checks to be performed before each use or daily.

Safety-Interlock System

Testing the Safety-Interlock System

Provides steps to test the proper functioning of the safety-interlock system.

Suspension System Adjustments

Adjusting the MyRide Suspension System

Details how to adjust the MyRide™™ suspension system for ride comfort.

Motion-Control Lever Adjustments

During Operation Safety

General Safety

Highlights general safety rules for operator attention and hazard avoidance during operation.

Slope Safety

Operating Controls

Operating the Mower Blade-Control Switch (PTO)

Instructions on engaging and disengaging the mower blades using the PTO switch.

Engine Starting and Stopping

Starting the Engine

Step-by-step procedure for starting the engine safely.

Shutting Off the Engine

Procedure for safely shutting off the engine.

Driving and Speed Control

Using the Smart Speed Control System

Explains how to use the Smart Speed™™ lever for different speed ranges.

Deck Height and Roller Adjustments

Adjusting the Height of Cut

Details how to adjust the mower deck's cutting height.

Adjusting the Anti-Scalp Rollers

Instructions for adjusting anti-scalp rollers for different deck sizes.

After Operation and Transport

After Operation Safety

Safety checks and procedures after operating the machine.

General Safety

Essential safety steps after operation, including cooling and cleaning.

Transporting the Machine

Instructions for safely transporting the mower using a trailer or truck.

Loading the Machine

Towing and Pushing the Machine

Towing the Machine

Guidelines for towing equipment safely with the mower.

Pushing the Machine by Hand

Important instructions for safely pushing the machine manually.

Maintenance Overview

Recommended Maintenance Schedule(s)

A schedule detailing maintenance tasks and their intervals.

Maintenance Safety

Critical safety warnings and precautions to follow during maintenance.

Pre-Maintenance Procedures and Lubrication

Pre-Maintenance Procedures

Steps to prepare the machine before performing maintenance.

Lubrication

Guidance on lubricating various parts of the mower.

Engine Maintenance

Engine Safety

Safety precautions related to engine maintenance.

Servicing the Air Cleaner

Air Cleaner Servicing

Servicing the Foam Air-Cleaner Element

Servicing the Paper Air-Cleaner Element

Engine Oil Servicing

Checking the Engine-Oil Level

Changing the Engine Oil and Oil Filter

Instructions for changing the engine oil and oil filter.

Spark Plug Servicing

Removing the Spark Plug

Checking the Spark Plug

Fuel and Cooling System Maintenance

Cleaning the Cooling System

Fuel System Maintenance

Replacing the In-Line Fuel Filter

Electrical System Maintenance

Electrical System Safety

Safety precautions for working with the electrical system and battery.

Servicing the Battery

Steps and safety for servicing the mower's battery.

Removing the Battery

Battery Charging and Installation

Charging the Battery

Installing the Battery

Fuse and Drive System Maintenance

Servicing the Fuses

Drive System Maintenance

Checking the Tire Pressure

Brake Release and Belt Maintenance

Belt Maintenance

Replacing the Mower-Deck Belt

Step-by-step guide to replace the mower deck belt.

Mower Maintenance

Blade Safety

Warnings and precautions regarding mower blade safety.

Servicing the Cutting Blades

Procedures for sharpening and maintaining mower blades.

Inspecting the Blades

Checking for Bent Blades

Blade Installation and Deck Leveling

Installing the Blades

Leveling the Mower Deck

Procedures to ensure the mower deck is level for proper cutting.

Leveling from Side to Side

Adjusting the Front-to-Rear Blade Slope

Removing the Mower Deck

Installing the Mower

Replacing the Grass Deflector

Storage Procedures

Storage Safety

Safety precautions to follow when storing the machine.

Cleaning and Storage

Troubleshooting Engine and Drive Issues

The engine overheats.

The starter does not crank.

The engine does not start, starts hard, or fails to keep running.

The engine loses power.

The machine does not drive.

Troubleshooting Mower Issues

There is an abnormal vibration.

The cutting height is uneven.

The blades do not rotate.

Toro TimeCutter 74760 Specifications

General

Engine Power	24 HP
Transmission	Hydrostatic
Ground Speed Forward	7 mph
Number of Blades	3
Washout Port	Yes
Speed	Variable
Deck Material	Steel
Fuel Capacity	3.5 gallons
Warranty	3 years
Cutting Height	1.5 - 4.5 in
Blade Tip Speed	18, 500 FPM
Spindle Material	Aluminum