Toro TimeCutter SS 4200 74720 User Manual (English)

Questions and Answers:

B
Brianna KirbyJul 30, 2025
What to do if my Toro TimeCutter SS 4200 74720 Lawn Mower engine will not start?
- J
  James DanielJul 30, 2025
  If your Toro Lawn Mower engine won't start, starts hard, or fails to keep running, first check if the fuel tank is empty and fill it if necessary. Ensure the choke is on. A dirty air cleaner can also cause this issue, so clean or replace it. Make sure the spark plug wire(s) is securely connected. Inspect the spark plug(s) for damage or incorrect gap and replace if needed. Also, check the fuel filter for dirt and replace if necessary. If there is incorrect fuel, drain the tank and replace the fuel with the proper type. Finally, ensure that the oil level in the crankcase is sufficient and add oil if needed. For issues related to dirt, water, or stale fuel in the fuel system, contact an Authorized Service Dealer.
M
murraycarrieAug 3, 2025
What to do if my Toro TimeCutter SS 4200 74720 Lawn Mower blades do not rotate?
- B
  Brianna TaylorAug 3, 2025
  If the blades on your Toro Lawn Mower do not rotate, it could be due to a worn, loose, or broken drive belt, in which case you should install a new drive belt. If the drive belt is off of the pulley, install it and check the adjusting shafts and belt guides for the correct position. If the Power Take-Off (PTO) switch or PTO clutch is faulty, contact an Authorized Service Dealer. Finally, check if the mower belt is worn, loose, or broken and install a new mower belt if needed.
M
Matthew AlvarezAug 8, 2025
Why does my Toro TimeCutter SS 4200 74720 have an uneven cutting height?
- T
  Timothy PopeAug 8, 2025
  Uneven cutting height on your Toro Lawn Mower can be caused by several factors. Start by sharpening the blade(s) if they are not sharp. Replace the cutting blade(s) if they are bent. Ensure the mower is level from side-to-side and front-to-rear. Adjust the anti-scalp wheel height if it is not set correctly. Clean the underside of the mower if it is dirty. Adjust the tire pressure if it is incorrect. If a blade spindle is bent, contact an Authorized Service Dealer.
C
carrie57Aug 11, 2025
Why does my Toro Lawn Mower engine overheat?
- D
  Dustin CruzAug 12, 2025
  Your Toro Lawn Mower engine may overheat due to several reasons. The engine load might be excessive, so reduce ground speed. Check if the oil level in the crankcase is low and add oil if needed. Also, inspect the cooling fins and air passages under the engine blower housing for obstructions and remove them. The air cleaner might be dirty, so clean or replace it. If the problem persists, it could be due to dirt, water, or stale fuel in the fuel system, in that case contact an Authorized Service Dealer.
D
Donna WilsonAug 16, 2025
What to do if my Toro TimeCutter SS 4200 74720 starter does not crank?
- A
  Andrew SextonAug 16, 2025
  If the starter on your Toro Lawn Mower does not crank, ensure that the blade control switch is disengaged. Also, make sure the motion control levers are in the park position. Check if the battery is dead and charge it if needed. Inspect the electrical connections for corrosion or looseness and ensure they have good contact. Replace the fuse if it is blown. For damaged relays or switches, contact an Authorized Service Dealer.
L
Lauren PottsAug 20, 2025
Why does my Toro TimeCutter SS 4200 74720 have abnormal vibration?
- K
  kvelasquezAug 21, 2025
  Abnormal vibration in your Toro Lawn Mower can stem from several issues. Check if the engine mounting bolts are loose and tighten them. Inspect the engine pulley, idler pulley, or blade pulley for looseness and tighten the appropriate pulley. If the engine pulley is damaged or a blade spindle is bent, contact an Authorized Service Dealer. Replace the cutting blade(s) if they are bent or unbalanced. Also, ensure that the blade mounting bolt is tightened.
L
Leah PopeAug 25, 2025
Why does my Toro TimeCutter SS 4200 74720 Lawn Mower not drive?
- G
  gabriel22Aug 25, 2025
  If your Toro Lawn Mower does not drive, it could be due to open bypass valves; close the tow valves. For issues related to worn, loose, or broken traction belts, traction belts being off of the pulleys, or a failed transmission, contact an Authorized Service Dealer.