Toro TimeCutter 74726

Questions and Answers

T
Tyler BarkerJul 27, 2025
Why does my Toro Lawn Mower engine not start, start hard, or fail to keep running?
- A
  Anna MiddletonJul 27, 2025
  Several factors can cause this issue. The fuel tank might be empty, so refill it. The air cleaner could be dirty, requiring cleaning or replacement. Check if the spark plug wire(s) is loose or disconnected and install the wire(s) on the spark plug. A spark plug(s) may be pitted, fouled, or have an incorrect gap, so install a new, correctly gapped spark plug(s). The fuel filter may be dirty, so replace it. The oil level in the crankcase might be low, so add oil to the crankcase. Finally, ensure that you are using the correct fuel type; if not, drain the tank and replace the fuel with the proper type.
R
Robert WilliamsJul 31, 2025
Why is my Toro TimeCutter 74726 Lawn Mower cutting height uneven?
- A
  Angelica ReyesJul 31, 2025
  An uneven cutting height on your Toro Lawn Mower can be due to several reasons. The blade(s) may not be sharp, so sharpen the blade(s). A cutting blade(s) may be bent, so install a new cutting blade(s). The mower might not be level, so level the mower from side-to-side and front-to-rear. An anti-scalp wheel may not be set correctly, so adjust the anti-scalp wheel height. The underside of the mower could be dirty, so clean it. Finally, the tire pressure might be incorrect, so adjust the tire pressure.
M
mary48Aug 4, 2025
What to do if the blades do not rotate on my Toro TimeCutter 74726 Lawn Mower?
- J
  Jasmin MeyerAug 4, 2025
  If the blades on your Toro Lawn Mower aren't rotating, it could be due to a worn, loose, or broken drive belt, so install a new drive belt. Alternatively, the drive belt might be off the pulley, so install the drive belt and check the adjusting shafts and belt guides for the correct position. Also, the mower belt could be worn, loose, or broken, so install a new mower belt.
H
Heather ScottAug 9, 2025
Why is my Toro Lawn Mower engine losing power?
- T
  terri07Aug 9, 2025
  A loss of power in your Toro Lawn Mower engine can stem from several causes: excessive engine load, which can be resolved by reducing ground speed; a dirty air cleaner, which requires cleaning; or a low oil level in the crankcase, necessitating the addition of oil. Furthermore, check for obstructions in the cooling fins and air passages under the engine blower housing and remove them if present. Ensure the spark plug(s) is in good condition; if pitted, fouled, or incorrectly gapped, replace it. Check the fuel filter for dirt and replace if necessary. Finally, if you are using incorrect fuel, drain the tank and replace it with the proper type.
B
Brady GarciaAug 13, 2025
What to do if my Toro TimeCutter 74726 Lawn Mower engine overheats?
- D
  Dale GainesAug 13, 2025
  If your Toro Lawn Mower engine is overheating, several factors could be the cause. First, the engine load might be excessive, so reduce the ground speed. Second, the oil level in the crankcase might be low, so add oil to the crankcase. Third, check the cooling fins and air passages under the engine blower housing for obstructions and remove them. Fourth, a dirty air cleaner can cause overheating, so clean or replace the air-cleaner element.
M
Matthew NunezAug 17, 2025
What to do if my Toro Lawn Mower starter does not crank?
- K
  Kelly GrantAug 17, 2025
  If the starter on your Toro Lawn Mower isn't cranking, here are a few things to check: Ensure the blade-control switch is disengaged. Make sure the motion-control levers are in the PARK position. Verify the battery isn't dead by charging it. Inspect the electrical connections for corrosion or looseness, and ensure they have good contact. Check for a blown fuse and replace it if necessary.
A
Autumn JacksonAug 21, 2025
What to do if my Toro TimeCutter 74726 Lawn Mower has an abnormal vibration?
- E
  emilyhornAug 22, 2025
  If your Toro Lawn Mower is vibrating excessively, check the following: Tighten any loose engine-mounting bolts. Ensure the engine pulley, idler pulley, or blade pulley is tightened appropriately. If the cutting blade(s) is bent or unbalanced, install a new cutting blade(s). Also, tighten any loose blade-mounting bolts.

Summary

Safety

Safety Alert Symbol

Identifies important safety messages to avoid accidents.

General Safety

Basic safety precautions for operating the machine and preventing injury.

Slope Indicator

Operation

Before Operation

Preparatory checks and safety procedures before starting.

Before Operation Safety

Essential safety checks and precautions before operating the mower.

Pre-Start

Final checks and procedures before starting the engine.

Fuel Safety

Precautions for safe handling of fuel to prevent fire or explosion.

Adding Fuel

Using the Safety-Interlock System

Understanding and testing the system designed to prevent unsafe operation.

During Operation Safety

Safety precautions to observe while the machine is in use.

Slope Safety

Guidelines for safe operation on slopes to prevent loss of control.

Operating the Blade-Control Switch (PTO)

Instructions for engaging and disengaging mower blades.

Starting the Engine

Step-by-step guide for safely starting the machine's engine.

Shutting Off the Engine

Procedure for safely stopping the engine and parking the machine.

Using the Motion-Control Levers

Driving the Machine

How to maneuver the machine, including its unique turning capabilities.

Using the Smart Speed Control System

Selecting speed ranges (trim, tow, mow) for different tasks.

Adjusting the Height of Cut

Operating Tips

After Operation

After Operation Safety

Safety procedures after the machine has been used.

Transporting the Machine

Detailed instructions for securing and transporting the mower.

Pushing the Machine by Hand

Maintenance

Recommended Maintenance Schedule(s)

Schedule of required maintenance tasks at different service intervals.

Maintenance Safety

Crucial safety precautions to follow before performing maintenance.

Pre-Maintenance Procedures

Engine Maintenance

Procedures for servicing the engine and its components.

Engine Safety

Safety guidelines specific to engine maintenance tasks.

Servicing the Air Cleaner

Instructions for cleaning or replacing the air cleaner element.

Servicing the Foam Air-Cleaner Element

Steps for cleaning and replacing the foam air filter element.

Servicing the Paper Air-Cleaner Element

Servicing the Engine Oil

Procedures for checking and changing engine oil and filter.

Checking the Engine-Oil Level

Changing the Engine Oil and Oil Filter

Step-by-step guide for draining and replacing engine oil and filter.

Removing the Spark Plug

Servicing the Spark Plug

Checking and replacing the spark plug at scheduled intervals.

Checking the Spark Plug

Installing the Spark Plug

Electrical System Maintenance

Electrical System Safety

Safety precautions for working with the electrical system.

Servicing the Battery

Procedures for removing, charging, and installing the battery.

Removing the Battery

Charging the Battery

Installing the Battery

Servicing the Fuses

Belt Maintenance

Releasing the Electric Brake

Replacing the Mower-Deck Belt

Procedure for replacing a worn or damaged mower deck belt.

Mower Maintenance

Blade Safety

Safety precautions when inspecting or servicing mower blades.

Servicing the Cutting Blades

Ensuring sharp blades for superior cut quality and longevity.

Inspecting the Blades

Checking blades for sharpness, wear, damage, or cracks.

Checking for Bent Blades

Installing the Blades

Leveling the Mower Deck

Ensuring the mower deck is level for an even cut.

Leveling from Side to Side

Adjusting the Front-to-Rear Blade Slope

Removing the Mower Deck

Installing the Mower

Replacing the Grass Deflector

Replacing the Grass Deflector (Stamped Decks)

Storage

Storage Safety

Safety precautions to take before storing the machine.

Cleaning and Storage

Steps for cleaning and preparing the machine for storage.

Storing the Battery

Troubleshooting