EasyManua.ls Logo

Toro TimeCutter 74768 - User Manual

Toro TimeCutter 74768
64 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
FormNo.3425-432RevD
TimeCutter
®
RidingMowers
ModelNo.74726—SerialNo.404314200andUp
ModelNo.74726TA—SerialNo.400000000andUp
ModelNo.74760—SerialNo.404314200andUp
ModelNo.74760TA—SerialNo.400000000andUp
ModelNo.74766—SerialNo.404314200andUp
ModelNo.74766TA—SerialNo.400000000andUp
ModelNo.74768—SerialNo.404314200andUp
ModelNo.74772—SerialNo.404314000andUp
ModelNo.74773—SerialNo.404314000andUp
ModelNo.74774—SerialNo.404310000andUp
ModelNo.74774TA—SerialNo.400000000andUp
ModelNo.74777—SerialNo.404314200andUp
ModelNo.74778—SerialNo.404314200andUp
Registeratwww.Toro.com.
OriginalInstructions(EN)
*3425-432*D

Table of Contents

Questions and Answers

  • B
    bryantrobinAug 5, 2025
    Why does my Toro Lawn Mower engine not start, start hard, or fail to keep running?
    • M
      Matthew SheltonAug 5, 2025
      Several factors can cause this issue. The fuel tank might be empty, so refill it. The air cleaner could be dirty, requiring cleaning or replacement. Check if the spark plug wire(s) is loose or disconnected and install the wire(s) on the spark plug. A spark plug(s) may be pitted, fouled, or have an incorrect gap, so install a new, correctly gapped spark plug(s). The fuel filter may be dirty, so replace it. The oil level in the crankcase might be low, so add oil to the crankcase. Finally, ensure that you are using the correct fuel type; if not, drain the tank and replace the fuel with the proper type.
  • K
    Kenneth HigginsAug 10, 2025
    Why is my Toro TimeCutter 74768 cutting height uneven?
    • K
      Kristen DaltonAug 10, 2025
      An uneven cutting height on your Toro Lawn Mower can be due to several reasons. The blade(s) may not be sharp, so sharpen the blade(s). A cutting blade(s) may be bent, so install a new cutting blade(s). The mower might not be level, so level the mower from side-to-side and front-to-rear. An anti-scalp wheel may not be set correctly, so adjust the anti-scalp wheel height. The underside of the mower could be dirty, so clean it. Finally, the tire pressure might be incorrect, so adjust the tire pressure.
  • R
    Rebecca WallaceAug 14, 2025
    What to do if the blades do not rotate on my Toro TimeCutter 74768?
    • C
      Crystal OwensAug 14, 2025
      If the blades on your Toro Lawn Mower aren't rotating, it could be due to a worn, loose, or broken drive belt, so install a new drive belt. Alternatively, the drive belt might be off the pulley, so install the drive belt and check the adjusting shafts and belt guides for the correct position. Also, the mower belt could be worn, loose, or broken, so install a new mower belt.
  • K
    Kenneth RodriguezAug 18, 2025
    Why is my Toro Lawn Mower engine losing power?
    • J
      Jack AliAug 18, 2025
      A loss of power in your Toro Lawn Mower engine can stem from several causes: excessive engine load, which can be resolved by reducing ground speed; a dirty air cleaner, which requires cleaning; or a low oil level in the crankcase, necessitating the addition of oil. Furthermore, check for obstructions in the cooling fins and air passages under the engine blower housing and remove them if present. Ensure the spark plug(s) is in good condition; if pitted, fouled, or incorrectly gapped, replace it. Check the fuel filter for dirt and replace if necessary. Finally, if you are using incorrect fuel, drain the tank and replace it with the proper type.
  • M
    Mary Buckley PhDAug 22, 2025
    What to do if my Toro TimeCutter 74768 Lawn Mower engine overheats?
    • J
      James OrrAug 22, 2025
      If your Toro Lawn Mower engine is overheating, several factors could be the cause. First, the engine load might be excessive, so reduce the ground speed. Second, the oil level in the crankcase might be low, so add oil to the crankcase. Third, check the cooling fins and air passages under the engine blower housing for obstructions and remove them. Fourth, a dirty air cleaner can cause overheating, so clean or replace the air-cleaner element.
  • M
    Monica JenningsAug 27, 2025
    What to do if my Toro Lawn Mower starter does not crank?
    • M
      Michael AcevedoAug 27, 2025
      If the starter on your Toro Lawn Mower isn't cranking, here are a few things to check: Ensure the blade-control switch is disengaged. Make sure the motion-control levers are in the PARK position. Verify the battery isn't dead by charging it. Inspect the electrical connections for corrosion or looseness, and ensure they have good contact. Check for a blown fuse and replace it if necessary.
  • T
    toni56Aug 31, 2025
    What to do if my Toro TimeCutter 74768 Lawn Mower has an abnormal vibration?
    • S
      Sylvia GreenAug 31, 2025
      If your Toro Lawn Mower is vibrating excessively, check the following: Tighten any loose engine-mounting bolts. Ensure the engine pulley, idler pulley, or blade pulley is tightened appropriately. If the cutting blade(s) is bent or unbalanced, install a new cutting blade(s). Also, tighten any loose blade-mounting bolts.

Summary

Safety

General Safety Guidelines

Provides fundamental safety guidelines for operating the lawn mower and avoiding hazards.

Slope Indicator

Product Overview

Machine Controls

Overview and operation of key machine controls including levers, switches, and indicators.

Operation Procedures

Before Operation Safety

Essential safety checks and precautions to take before starting the mower operation.

Fuel Safety Precautions

Adding Fuel and Fuel System

Recommended Fuel and Additives

Safety-Interlock System

During Operation Safety

Slope Safety Procedures

Operating Blade Controls

Starting and Stopping the Engine

Using Motion-Control Levers

Driving the Machine

Smart Speed Control System

Adjusting Cutting Height and Rollers

Adjusting the Height of Cut

After Operation Procedures

After Operation Safety

Safety procedures to follow after finishing operation, including parking and cooling the machine.

Transporting the Machine

Guidelines and safety precautions for transporting the mower using a trailer or truck.

Loading the Machine Safely

Towing and Pushing the Machine

Towing the Machine Safely

Maintenance Schedule and Safety

Recommended Maintenance Schedule

A schedule outlining maintenance procedures based on operating hours or time intervals.

Maintenance Safety Precautions

General safety precautions to be observed while performing maintenance on the machine.

Lubrication Procedures

Greasing the Bearings

Engine Maintenance

Engine Safety and Air Cleaner Service

Safety precautions for engine maintenance and servicing the air cleaner element.

Engine Oil Service

Engine Oil Specifications and Level Check

Changing Engine Oil and Filter

Step-by-step guide for changing the engine oil and oil filter.

Spark Plug Service

Removing and Checking the Spark Plug

Cooling System and Fuel System Maintenance

Replacing the In-Line Fuel Filter

Electrical System Maintenance

Electrical System Safety

Safety precautions for working with the mower's electrical system and battery.

Battery Service

Instructions for servicing the battery, including removal, safety, charging, and installation.

Fuse Service and Tire Pressure

Checking the Tire Pressure

Electric Brake and Belt Maintenance

Replacing the Mower-Deck Belt

Step-by-step guide for replacing the mower deck belt, including signs of wear.

Mower Maintenance

Blade Safety and Service

Procedures for blade safety, inspection, removal, installation, sharpening, and balancing.

Mower Deck Leveling

Leveling Side-to-Side

Adjusting Front-to-Rear Blade Slope

Removing the Mower Deck

Installing the Mower Deck

Storage Procedures

Storage Safety

Safety precautions to take before storing the machine, such as cooling the engine.

Cleaning and Preparing for Storage

Troubleshooting Common Issues

Toro TimeCutter 74768 Specifications

General IconGeneral
EngineKohler 7000 Series
TransmissionHydrostatic
Spindle MaterialCast iron
Engine BrandKohler
Drive SystemRear-wheel drive
Ground Speed Forward7 mph
Ground Speed Reverse3 mph
Number of Blades2
Washout PortYes
Hour MeterYes
Fuel Capacity3 gal
Blade Tip Speed18, 000 FPM
Cutting Height1.5 - 4.5 inches
Seat TypeHigh back
Rear Tire Size20 x 10-8
Warranty3 years
SpeedVariable
Turning RadiusZero-Turn

Related product manuals