Chapter
5:
Setting
up
your
TV
To
set
the
HDMI
audio
mode:
Setting
the
HDMI®
audio
mode
Setting
the
time
zone
The
Time
Zone
setup
will allow
you
to
specify
the
correct
time
70ne
for
your
region.
This
feature will
allow
the
TV
status
information
to
show
the
correct
time
mne
information
(
page
58).
the
HDM'
1
Audio
setting changes to "Auto. "
If
PC
Audio
is
set to "Yes," the HOM' 1
Audio
setting
is
set to
"Digital"
and
is
grayed
out
in
the menu. (Also see item 4 on
page
12
and
"Setting the PC
Audio"
on
page
50.)
Viewing
the
digital
signal
meter
You
can
view the digital signal
meter
in
the
ANTI
CABLE
digital
TV
input
source
only.
To
view the digital signal meter:
1
MENU
Press 0
and
open
the
Setup
menu.
2
Highlight
Installation
and
press
@.
3 A new set
of
Installation
menu
icons
will appear.
Open
the
Terrestrial
menu.
highlight
Signal
Meter.
and
press
@.
4
Press
& T
<OIII~
to
select
the
antenna
input
and
digital
channel
whose
signal you
want
to
check.
Note:
•
The
physical digital channel number listed
in
the
Signal Meter screen may not correspond
to
a virtual
TV
channel number. Contact your
local broadcasters
to
obtain
the
RF
channel
numbers for your local digital stations.
•
The
signal strength does not change between
virtual channels
on
the
same physical
channel.
To close the screen
and
return
to
the
Terrestrial menu:
Highlight
Done
and
press
@.
To
return
to
normal
viewing:
EXIT
Press
O.
When
viewing
the
HDMI
I input.
digital
audio
from
the
HDMI
input will
be
output.
When
viewing
the
HDMI
I input.
if
digital
audio
from
the
HDMI
input is
available. it will be
output.
If
not. the
TV
will
automatically
detect
and
output
analog
audio
from the PC
Audio
input.
Description
Digital
Auto
Mode
4
Highlight
Done
and
press@
to save
changes.
and
go
back to
the
Channel
Labeling
window.
1
MENU
Press
0
and
open
the
Sound
menu.
2
Highlight
Audio
Setup
and
press
@.
3 Press &
or
T
to
select
HDMI1
Audio
and
then press
<011I
or
~
to
select
the
HDMI
I
audio
mode
(Auto.
Digital.
or
Analog).
(Auto
is
the
recommendcd
mode.)
See
"Connecting
an
HDMI
or
DVI
device
to
the
HDMI
input"'
(1Gf'
page
16).
4 To save
your
settings,
highlight
Done
and
press
@.
Note: Because the PC
and
HOMI-1 inputs
share the same set
of
analog audio inputs, the
PC
Audio
menu setting influences the HOM' 1
Audio
menu setting.
If
PC
Audio
is
set to "No, "
Analog
When
viewing
the
HDMI
I input.
analog
audio
from
the
PC
Audio
input
will
be
output.
To
set the time zone:
1 From the
Setup
menu, highlight Installation and
press
@.
A new set
of
Installation menu icons
wi
II
appear.
2 Highlight
Time
Zone.
and
press@.
3 Press
<011I
or
~
to
select
the
region, highlight
Done.
and
then
press
@.
(cOlllillued)
33
I
To Next Page
Loading...
Need help?
General