Toshiba E-studio3040c

To Next Page

To Previous Page

2 SETTING ITEMS (ADMIN)

138 Setting Network Functions

Continue to another network setting if required, then press [APPLY NOW].

“NETWORK INITIALIZING” is displayed at the lower left of the screen and this equipment starts initializing the

network interface card to apply the changes. This message disappears after it is finished.

Main Page

Preface3
- Table of Contents5
- Contents5
Chapter 1 Setting Items (User)9
Entering User Menu10
Setting General Functions11
- Changing the Display Language11
- Setting the Reversed Display Mode12
- Adjusting the Display Contrast14
- Setting the Calibrations15
- Setting the Registration17
Setting Copy Functions18
Setting Fax Functions24
Setting Scan Functions26
Setting E-Filing Functions29
Printing Lists30
Setting Drawer33
Managing Address Book37
- Managing Contacts in Address Book37
  - Editing Contacts43
  - Deleting Contacts45
- Managing Groups in Address Book52
  - Editing Groups55
  - Deleting Groups63
Checking E-Mail72
Setting BIP Printing73
Change User Password74
Chapter 2 Setting Items (Admin)75
Entering Admin Menu77
Setting General Functions79
- Setting the Device Information79
- Setting the Notification82
- Changing the Administrator Password and Resetting the Service Password84
- Changing the Administrator Password85
- Setting the Date and Time87
- Setting the Energy Saver Modes90
- Setting the Calibration and Registration Display Level95
- Setting the Calibration96
- Setting the Registration101
- Setting the Option102
- Setting the Drawer Set Pop-Up and Paper Misfeed Recovery Pop-Up103
- Setting the Status Message104
- Setting the Auto Clear Function105
- Managing the Option Licenses107
- Adding or Removing the Display Languages111
- Updating Your System116
- Creating or Installing Cloning Files119
- Setting the Panel Calibration126
- Touch Panel128
- Exporting Logs129
- Job Skip131
- Changing the Keyboard Layout133
- Usb Keyboard135
Setting Network Functions136
- Setting the TCP/IP Protocol (Ipv4)136
- Setting the Ipv6 Protocol141
- Setting the IPX/SPX Protocol150
- Setting the Netware Settings151
- Setting the SMB Protocol153
- Setting the Appletalk Protocol155
- Setting the HTTP Network Service157
- Setting the Ethernet Speed159
- Setting the LDAP Services and the Filtering Functions161
- Ipsec (IP Security) Setting163
- Network Check165
Setting Copy Functions168
Setting Fax Functions171
- Setting the Discard and Reduction Print Option for the RX Print171
Setting File Functions173
Setting E-Mail Functions174
Setting Internet Fax Functions177
Setting Security Functions179
- Managing Certificates179
- Setting Secure PDF187
- Performing the Integrity Check189
Setting List/Report192
- Setting the Communication Report194
Printing Lists197
Setting Printer/E-Filing Functions198
Wireless Settings and Bluetooth Settings201
Change User Password202
IEEE 802.1X Authentication Setting203
- Setting IEEE802.1X Authentication203
- Error Messages216
Resetting the Equipment Settings Back to the Factory Defaults217
Chapter 3 Managing Counters (Counter Menu)219
Total Counter220
Print out Total Counter223
Department Counter224
Managing Department Codes228
- Logging on as Administrator228
- Printing DEPARTMENT CODE LIST230
- Enabling Department Codes231
- Registering a New Department Code232
- Department Code234
- Editing Department Codes235
- Deleting Department Codes238
- Resetting the Counter for each Department239
- Setting Output Limitations for All Departments241
- Setting the no Limit Black Function242
- Setting the Registered Quota243
- Resetting All Department Counters244
- Deleting All Department Codes245
Chapter 4 APPENDIX248
List Print Format248
- Total Counter List248
- Department Code List249
- Address Book Information250
- Group Number Information251
- FUNCTION LIST (User)252
- NIC Configuration Page253
- FUNCTION LIST (Administrator)255
- PS3 Font List274
- PCL Font List275
Index277

Toshiba E-studio3040c - Page 140

Table of Contents

Other manuals for Toshiba E-studio3040c

Related product manuals