To Next PageTo Next PageWhat does error H16 mean on a Toshiba MMY-MUP2201HT8P-E?
If your Toshiba Air Conditioner displays error code H16, it indicates Oil level detector circuit trouble. It could be TK1 or TK2 oil circuit trouble.
Why does my Toshiba MMY-MUP2201HT8P-E Air Conditioner remote controller display a check code?
If your Toshiba Air Conditioner displays a check code on the remote controller, it might be due to duplicated addresses. Here's how to address it: 1. **Indoor Addresses:** Ensure that indoor unit addresses are not duplicated. If duplicates are found, reconfigure the address settings. 2. **Outdoor Addresses:** If you manually set up outdoor addresses, avoid doing so, as this can cause conflicts. 3. **Line Addresses:** If you connected U1/U2 and U3/U4 connectors, modify the line address setup of the header unit between lines by setting up SW13 and SW14 on the interface PC board.
What to do if a Toshiba Air Conditioner check code appears after installing an outdoor backup?
If your Toshiba Air Conditioner shows a check code, and you've recently installed an outdoor backup or noticed a decrease in connected outdoor units, here’s what to do: * **Outdoor Backup Installation:** If the error occurred during backup installation, clear the trouble code after the setup is complete. * **Follower Unit Power:** Ensure that the power to any follower units is turned on. If it's off, switch it on.
What if a check code on Toshiba MMY-MUP2201HT8P-E persists after troubleshooting steps?
If a check code is still appearing on your Toshiba Air Conditioner remote after trying other solutions, the issue might be with the interface PC board. In this case, the suggested solution is to replace the interface PC board.
What if a Toshiba MMY-MUP2201HT8P-E Air Conditioner check code is caused by address setup trouble?
If your Toshiba Air Conditioner is showing a check code, and the address setup is the cause, the suggested solution is to set up the addresses again. Modify the setup.
What does error E31 mean on a Toshiba MMY-MUP2201HT8P-E?
Error code E31 on your Toshiba Air Conditioner indicates an inverter communication trouble, or communication trouble between MCU and sub MCU.
What does error E19 mean on a Toshiba MMY-MUP2201HT8P-E Air Conditioner?
Error E19 on your Toshiba Air Conditioner indicates Number of header outdoor unit trouble.
Why does my Toshiba MMY-MUP2201HT8P-E show error E06?
Error E06 on your Toshiba Air Conditioner can be due to a decrease in the number of indoor units. In a TU2C-LINK communication system, this error can also occur if the termination resistance is not set in any of the indoor units.
What does error H08 mean on a Toshiba MMY-MUP2201HT8P-E Air Conditioner?
If your Toshiba Air Conditioner displays error code H08, it indicates temperature sensor trouble for oil level. It could be TK1 or TK2 sensor trouble.
What does error F09 mean on a Toshiba Air Conditioner?
If your Toshiba Air Conditioner displays error code F09, it indicates TG1, TG2 or TG3 sensor trouble.
General| Brand | Toshiba |
|---|---|
| Model | MMY-MUP2201HT8P-E |
| Category | Air Conditioner |
| Language | English |
Explains the use of R410A refrigerant for environmental friendliness.
Defines essential protective gear for handling the air conditioner.
Details important warnings and cautions for the air conditioner unit.
Covers general safety for operation, transport, installation, and repairs.
Safety instructions for unit repairs and relocation procedures.
Identifies key parts of the outdoor air conditioner unit.
Details components of various indoor unit types.
Illustrates parts for 4-way, 2-way, and concealed duct indoor units.
Shows parts for high static, slim duct, under ceiling, and floor standing units.
Explains all icons displayed on the remote controller screen.
Describes how to operate the air conditioner using the remote.
Details requirements for standby and running operations.
Explains how to set and cancel the unit's OFF timer.
Guidance for louver direction in 4-way, 1-way, and 2-way cassette units.
Instructions for under ceiling and floor standing unit louver adjustments.
Explains how to manually change the louver angle.
Recommendations for choosing the best installation site.
Advice on managing operation sounds and vibrations.
Covers pre-operation steps, heating performance, and defrosting.
Details protective devices, power failures, and operational limits.
Explains simultaneous cooling/heating and heating characteristics.
Advice on cleaning filters, managing windows, and temperature control.
Important warnings and cautions for daily maintenance tasks.
Instructions for cleaning air filters and recommended conditions.
Specifies optimal temperature and humidity for operation.
Procedures for cleaning indoor units and remote controllers.
Guidance for long-term storage and periodic inspections.
Essential checks before operating the unit.
Steps to check before requesting repair services.
How to confirm issues and check the troubleshooting history.
Details sound power levels and weights for various models.
Manufacturer's compliance statement with relevant directives.
