190 Q9 ASD Installation and Operation Manual
Table 7. Terminal Assignments With the Associated My Function Input Setting (Input Function Target) and
Parameter Setting Numbers for the FL, O1A/O1B (OUT1), O2A/O2B (OUT2), OUT3–OUT6, R1–R4
Terminals.
Discrete Output Terminal Assignment Selections
Input
Setting
Param
Setting
Function
Input
Setting
Param
Setting
Function
1000 0 Lower-Limit (LL) Frequency 1088 88 Error Code Output 5
1002 2 Upper-Limit (UL) Frequency 1090 90 Error Code Output 6
1004 4 Low (Speed Signal) 1092 92 Data Output 1
1006 6 Acceleration/Deceleration Complete 1094 94 Data Output 2
1008 8 Reach Speed Signal 1096 96 Data Output 3
1010 10 Fault (Any) 1098 98 Data Output 4
1012 12 Fault 2 (Except EF, OCL, EPHO, OL2) 1100 100 Data Output 5
1014 14 Over-Current (OC) Alarm 1102 102 Data Output 6
1016 16 ASD Overload (OL1) Alarm 1104 104 Data Output 7
1018 18 Motor Overload (OL2) Alarm 1106 106 Light Load Detected
1020 20 Over-Heat (OH) Alarm 1108 108 Heavy Load Detected
1022 22 Over-Voltage (OP) Alarm 1110 110 Positive Torque Limit
1024 24 DC Under-Voltage Alarm 1112 112 Negative Torque Limit
1026 26 Low-Current Alarm 1114 114 Rush Suppression Relay Activated
1028 28 Over-Torque (OT) Alarm 1118 118 Completion of Positioning (Not Used)
1030 30 DBR Overload (OL) Alarm (Not Used) 1120 120 L-STOP
1032 32 Emergency Off (E-Off) Active 1122 122 Power Fail Synchronize Op. (Not Used)
1034 34 Retry Active 1124 124 Traverse in Progress (Not Used)
1036 36 Pattern Operation Switching Output (Not Used) 1126 126 Traverse Deceleration in Progress (Not Used)
1038 38 PID Deviation Limit 1128 128 Maintenance Alarm
1040 40 Start/Stop 1130 130 Over-Torque (OT) Alarm
1042 42 Hard Fault (OCA, OCL, EF, Phase Failure, etc.) 1132 132 Frequency Command ½ Selection
1044 44 Soft Fault (OL, OC, OV) 1134 134 Fault (Except Emergency Off)
1046 46 Bypass 1 (Comm. Power/ASD Switching Output 1) 1135 136 Local/Remote
1048 48 Bypass 2 (Comm. Power/ASD Switching Output 2) 1138 138 Forced Run
1050 50 ASD Fan ON/OFF 1140 140 Fire Speed
1052 52 Jogging (Jog Run Active) 1142 142 Low Torque
1054 54 (Panel/)Terminal Board Operation Switching 1144 144 Frequency Control = RR
1056 56 Run-Time Alarm 1146 146 Frequency Control = RX
1058 58 Comm. Alarm (ProfiBus/DeviceNet/CC-Link) 1148 148 Frequency Control = VI
1060 60 Forward/Reverse Switching 1150 150 PTC Alarm
1062 62 Ready for Operation 1 (Includes ST and Run) 1152 152 Power Loss
1064 64 Ready for Operation 2 1154 154 4 – 20 mA Loss
1066 66 POFF Alarm (Control Power Out Of Spec.) 1156 156 Damper Command
1068 68 Brake Release (BR) (Not Used) 1222 222 My Function Output 1
1070 70 Alarm Status Active 1224 224 My Function Output 2
1072 72 Forward Speed Limit (Torque Control) 1226 226 My Function Output 3
1074 74 Reverse Speed Limit (Torque Control) 1228 228 My Function Output 4
1076 76 ASD Healthy Output 1230 230 My Function Output 5
1078 78 External Communication Error 1232 232 My Function Output 6
1080 80 Error Code Output 1 1234 234 My Function Output 7
1082 82 Error Code Output 2 1236 236 My Function Output 8
1084 84 Error Code Output 3 1238 238 My Function Output 9
To Next Page
Loading...
