What does it mean if the outdoor unit inverter Idc is activated on my Toshiba RAV-SM1403DT-A?
If the outdoor unit inverter Idc is activated on your Toshiba Air Conditioner, it indicates that short-circuit protection for compressor drive circuit devices (G-Tr/IGBT) was activated.
What to do if my Toshiba RAV-SM1403DT-A Air Conditioner drainage is out of order?
If the drainage of your Toshiba Air Conditioner is out of order, check the drain pipe for any clogging. Also, inspect the float switch circuit and the indoor P.C. board.
What to do if my Toshiba Air Conditioner is not receiving data from the remote controller or network adapter?
If your Toshiba Air Conditioner is not receiving data from the remote controller or network adapter, check the remote controller, the network adapter, and the indoor P.C. board.
What does it mean if my Toshiba RAV-SM1403DT-A detects an open phase?
If your Toshiba Air Conditioner indicates an open phase, the power cable might be connected incorrectly. Verify the open phase and voltages of the power supply.
What causes an indoor unit fan error in my Toshiba Air Conditioner?
An indoor AC fan error on your Toshiba Air Conditioner indicates that the fan motor thermal relay has been activated, likely due to an issue with the indoor P.C. board.
What causes an outdoor unit fan error on my Toshiba RAV-SM1403DT-A?
An error in the outdoor unit fan of your Toshiba Air Conditioner (such as overcurrent or locking) indicates a problem in the outdoor unit fan drive circuit, potentially related to the Outdoor P.C. board.
What does it mean if my Toshiba RAV-SM1403DT-A displays an outdoor unit compressor breakdown?
If your Toshiba Air Conditioner reports an outdoor unit compressor breakdown, it means that the minimum frequency was reached in the current releasing control or short-circuit current (Idc) after direct excitation was detected.
What causes a heat sink overheat in my Toshiba RAV-SM1403DT-A Air Conditioner?
If your Toshiba Air Conditioner's heat sink is overheating, it signifies that the temperature sensor of the IGBT heat sink has detected an abnormal temperature.
What does it mean if my Toshiba Air Conditioner displays an outdoor unit high-pressure system error?
If your Toshiba Air Conditioner is showing a high-pressure system error, the IOL was activated, or an error was detected in the high-pressure releasing control using the TE.
What does it mean if my Toshiba Air Conditioner displays an outdoor unit discharge temp. error?
If your Toshiba Air Conditioner indicates an outdoor unit discharge temp. error, an error was detected in the discharge temp. releasing control.
General| Brand | Toshiba |
|---|---|
| Model | RAV-SM1403DT-A |
| Category | Air Conditioner |
| Language | English |
Covers critical warnings for installation, operation, and repair/movement safety.
Covers important cautions for installation and operation safety.
Identification of parts for the indoor air conditioner unit.
Overview of the separate sold remote controller.
Identification of parts for the outdoor air conditioner unit.
Explanation of indicators and symbols on the remote controller display.
Description of buttons and functions in the remote controller operation section.
Steps to take before starting the air conditioner for the first time.
Procedures for initiating and safely stopping the air conditioner's operation.
Guide to setting up different timer modes for operation.
Instructions for canceling an active timer setting.
Steps to activate the power saving mode of the air conditioner.
How to disable the power saving mode.
Detailed instructions for configuring power saving settings.
Advice on maintaining efficiency and reducing energy consumption.
Understanding how the protective device stops operation and what to do.
Procedure for cleaning the air filters and resetting the indicator.
Guidelines for cleaning the remote controller safely.
Recommended checks for long-term use and preparing for storage.
Explanation of the 3-minute protection and power failure handling.
Details on preheating, warm air control, and defrosting.
Recommended temperature and humidity ranges for optimal performance.
Guidance on suitable and unsuitable places for installing the unit.
Precautions and requirements for electrical connections and grounding.
Steps to check before contacting service for common problems.
Explanations for noises, smells, or mist that are not actual failures.
To Next Page
