Reference Information
Toshiba 2-9
25
RECORDING
Timer Programming Procedure
Example: To record cable channel 25 in the SP tape speed from
9:20 p.m. until 10:00 p.m. on August 30. Today is August 25.
1
Load a cassette with the safety tab attached.
2
Press
PROG
. to display the MENU screen.
3
Select “PROGRAM” using
FF
or
REW
, and press
ENTER
.
4
Move to the next using
FF
, and
select the channel number 25 by
pressing
number buttons
2 and 5,
PLAY
or
STOP.
• You can make “L” appear on the channel number position by
pressing
I.SELECT
depending on your connection.
(See pages 12 ).
To make corrections:
Press
REW
to move back to the item, or
FF
to forward.
(Continued)
Timer Program Recording
The programmable timer allows you to record up to 6 different programs over one month.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• Make sure that the clock is set correctly (page 15).
• Store the channels on the VCR (pages 16 and 17).
RECORDING
2, 9
SLOW
PAUSE/STILL
STOP
FF
REC
TIMER
VC-413
TV
VCR
POWER
I.SELECT
SP/ SLP
DISPLAY
TV VOL
COUNTER
PROG.
CANCEL
REW
PLAY
REMAIN/
RESET
COUNT
EJECT
REW
STOP
FF
PLAY
10
1
2
3
4
0
100
6
9
8
7
5
ENTER
Number
buttons
FF
STOP
REW
ENTER
PLAY
24
Watching a TV program while
recording another
1) While recording, press
TV/VCR
to turn off
“VCR” indicator.
2) Choose another channel using the channel
selector on the TV.
Skipping unnecessary scenes while
recording
Press
PAUSE/STILL
to stop recording
momentarily. To resume recording, press
PAUSE/STILL
again.
Note
The VCR automatically shifts to the stop mode if the
recording pause mode continues for 10 minutes.
Basic Recording
1
Load a cassette with the safety tab attached.
2
Press
TV/VCR
so that the “VCR”
indicator appears in the VCR display.
3
Select a channel to record with
CHANNEL
on the VCR, or
CH/TRK
or
number buttons
on the remote
control.
If you see “L” in the VCR display, press
I.SELECT
so that the channel
number appears.
• If you record cable channels via the cable box, make the output
channel number of the cable box or “L” appear, depending on your
connection. (See pages 11 – 12.)
4
Press
SP/SLP
to select the
recording tape speed.
SP: Suitable for general recording with
better picture and sound quality.
SLP: Suitable for tripling recording time, but with less picture and
sound quality than using the SP tape speed.
5
Press
REC
on the VCR, or
simultaneously press both
REC
on
the remote control.
Recording starts.
6
Press
STOP
to stop recording.
Recording off time setting
By setting the recording off time, the recording
stops and the VCR is turned off automatically.
While recording, press simultaneously both
REC
on the remote repeatedly to set the desired off
time.
Each time you press
REC
, each half-hour up to
about 4 hours appear cyclically.
Notes
• To cancel the recording in progress, press
POWER
on the VCR
.
VCR
H
ST
S
VCR
L
S
VCR
REC
L
TIMER
S
VCR
L
TIMER
Hi-Fi
STEREO
SAP
VCR
L R
TIMER
RECORDING
Recording a TV Program
This section explains the basic recording operation.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
To record from other
connected equipment
In step 3, press
I.SELECT
to
switch the display as follows:
L: To record via the LINE IN
jacks on the rear panel.
.
REC
TIMER
6
2
5
SLOW
PAUSE/STILL
STOP
FF
REC
TIMER
VC-413
TV
VCR
POWER
I.SELECT
SP/ SLP
DISPLAY
TV VOL
COUNTER
PROG.
CANCEL
REW
PLAY
REMAIN/
RESET
COUNT
EJECT
STOP
I.SELECT
4
3
1
2
3
4
5
0
100
6
9
8
7
ENTER
To Next Page
Loading...
