Reference Information
Toshiba 2-9
25
RECORDING
Timer Programming Procedure
Example: To record cable channel 25 in the SP tape speed from
9:30 p.m. until 10:00 p.m. on August 30. Today is August 25.
1
Load a cassette with the safety tab attached.
2
Press PROG. to display the MENU screen.
3
Select “PROGRAM” using CURSOR
( ) or ( ), and press ENTER.
4
Move to the next using CURSOR
( ), and select the channel number
25 by pressing number buttons 2
and 5 or using CURSOR (
▲
) or (
▼
).
• To record a cable program from the connected cable box:
Enter the cable channel number using CURSOR (
▲
), (
▼
) or by
pressing number buttons.
If your cable box is not remote-controllable, choose the desired
channel (1 to 125) on the cable box.
To make corrections:
Press CURSOR ( ) to move back to the item, or CURSOR ( ) to
forward.
(Continued)
Timer Program Recording
The programmable timer allows you to record up to 6 different programs over one month.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• Make sure that the clock is set correctly (page 15).
• Store the channels on the VCR (pages 16 and 17).
• If you record cable channels, finish the cable box set-up (pages 12), and turn on the cable box.
RECORDING
E
n
D : PROG
SET UP
PRESET
PROGRAM
CH DATE O
n
OFF SPD
- - -/-- -:- - -:- - -
- - -/-- -:- - -:- - -
- - -/-- -:- - -:- - -
- - -/-- -:- - -:- - -
- - -/-- -:- - -:- - -
- - -/-- -:- - -:- - -
E
n
D : PROG
SET UP
PRESET
PROGRAM
CH DATE O
n
OFF SPD
- - -/-- -:- - -:- - -
- - -/-- -:- - -:- - -
- - -/-- -:- - -:- - -
- - -/-- -:- - -:- - -
- - -/-- -:- - -:- - -
2 5 -/-- -:- - -:- - SLP
▼
▼
▼
▼
▼
CANCEL
3
2,9
10
4
CURSOR
24
Watching a TV program while
recording another
1) While recording, press TV/VCR to turn off
“VCR” indicator.
2) Choose another channel using the channel
selector on the TV.
Skipping unnecessary scenes while
recording
Press PAUSE to stop recording momentarily. To
resume recording, press PAUSE again.
Note
The VCR automatically shifts to the stop mode if the
recording pause mode continues for 10 minutes.
Basic Recording
1
Load a cassette with the safety tab attached.
2
Press TV/VCR so that the “VCR”
indicator appears in the VCR display.
3
Select a channel to record with
CHANNEL on the VCR, or CH/TRK
or number buttons on the remote
control.
If you see “L1” or “L2” in the VCR display, press INPUT SELECT so
that the channel number appears.
• If you record cable channels via the cable box, make the output
channel number of the cable box or “L1” appear, depending on your
connection. (See pages 11 – 12.)
4
Press SP/SLP to select the
recording tape speed.
SP: Suitable for general recording with
better picture and sound quality.
SLP: Suitable for tripling recording time, but with less picture and
sound quality than using the SP tape speed.
5
Press REC on the VCR, or
simultaneously press both REC on
the remote control.
Recording starts.
6
Press STOP to stop recording.
Recording off time setting
By setting the recording off time, the recording
stops and the VCR is turned off automatically.
While recording, press simultaneously both REC
on the remote repeatedly to set the desired off
time.
Each time you press REC, each half-hour up to
about 4 hours appear cyclically.
Notes
• To cancel the recording in progress, press
POWER on the VCR.
S L P
VCR
REC
TIMER
H
ST
S L P
S
VCR
REC
L
TIMER
S
S L P
VCR
REC
L
TIMER
S
S L P
VCR
REC
L
TIMER
Hi-Fi
STEREO
S L P
SAP
VCR
REC
L R
TIMER
RECORDING
Recording a TV Program
This section explains the basic recording operation.
Preparation
• Select the video channel (3 or 4) or video input mode on the TV.
• If you record cable channels via the cable box, finish the cable box set-up (pages 12), and turn on the cable
box.
To record from other
connected equipment
In step 3, press I
NPUT SELECT
to switch the display as follows:
L1: To record via the LINE IN 1
jacks on the rear panel.
L2: To record via the LINE IN 2
jacks on the front panel.
TIMERREC
INPUT
SELECT
3
2
6
5
4
To Next Page
Loading...
