TP-Link TL-WPA7510 KIT - User Manual

Ethernet Cable
Extender
TL-WPA7510
Adapter
TL-PA7010
Powerline
Router
1
Internet
1000Mbps
LAN
On
2
Plug in the adapter and extender in the
same room. Wait for about 30 seconds
until the extender’s 2.4GHz and 5GHz
Wi-Fi LEDs turn on.
Note: If only one wall outlet is available, plug both
devices into a power strip for setup, then relocate
to wall outlets before enjoying the internet.
1000Mbps
* TL-WPA7510 KIT (European version) is
used for demonstration in this QIG.
Pair the powerline devices.
4
3
Note: If the Powerline LED turns red, it means the signal strength is poor. Try another wall outlet.
Relocate the extender to the Wi-Fi “dead” zone on the same electrical circuit. Connect your devices
to the internet using the default SSID (network name) and password on the Wi-Fi Info Card provided.
Tips:
Want to unify Wi-Fi networks or
personalize your network?
See the back page for instructions.
Attention
Wall Outlet Power Strip
Plug powerline devices into wall outlets. Do not use power strips after setup.
Note: If the LED does not blink, press the
button again.
Press the adapter‘s Pair button for 1 second.
The Power LED starts blinking.
A
Within 2 minutes, press the extender’s Pair button for 1 second.
The Power LED starts blinking.
B
When the Powerline LED turns on, the pairing process is
complete.
Extender TL-WPA7510
Within 2 minutes
Adapter TL-PA7010
1000Mbps
PairLED
Wi-Fi
Reset
Pair
1000Mbps
Blinking
Blinking
On
Quick Installation Guide
TL-WPA7510 KIT

TP-Link TL-WPA7510 KIT Specifications

General

Modulation	OFDM
Power plug	-
Ethernet LAN	Yes
Wi-Fi standards	802.11a, Wi-Fi 5 (802.11ac), 802.11b, 802.11g, Wi-Fi 4 (802.11n)
PowerLine standard	HomePlug AV2
Top Wi-Fi standard	Wi-Fi 5 (802.11ac)
Security algorithms	128-bit AES, WPA, WPA2, WPS
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3ab, IEEE 802.3u
Built-in power socket	No
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN (RJ-45) ports	1
Maximum data transfer rate	1000 Mbit/s
Maximum operating distance	300 m
Ethernet LAN interface type	Gigabit Ethernet
Copper ethernet cabling technology	10BASE-T, 100BASE-TX, 1000BASE-T
WLAN data transfer rates supported	300, 433 Mbit/s
Antenna type	Internal
Certification	FCC, CE
Product color	White
Cables included	LAN (RJ-45)
Quantity per pack	2 pc(s)
Power consumption (standby)	2.2 W
Sustainability certificates	RoHS
Storage temperature (T-T)	-40 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 90 %

Weight and Dimensions

Depth	70.8 mm
Width	135.6 mm
Height	49 mm
Package depth	190 mm
Package width	230 mm
Package height	100 mm
Package weight	730 g

Summary

Quick Installation

Plug In Adapter and Extender

Connect adapter and extender, wait for LEDs to stabilize.

Pair Powerline Devices

Press pair buttons on both devices within 2 minutes to link them.

Enjoy Your Network

Relocate extender and connect devices for internet access.

Wall Outlet Usage Note

Use wall outlets for powerline devices; avoid power strips after setup.

Advanced Network Setup

Unify Wi-Fi Networks via Auto-Sync

Use Wi-Fi Auto-Sync to create a single Wi-Fi network by copying router settings.

Copy Router Settings via WPS

Press WPS buttons on router and extender to copy SSID and password.

Sync Settings to Additional Extenders

Automatically sync Wi-Fi settings from existing extenders to new ones.

Personalize Network Settings

Manage network settings using tpPLC app, utility, or web interface.

Troubleshooting and Support

Frequently Asked Questions

Answers to common issues like resetting devices or connectivity problems.

Technical Support Information

Contact information and resources for further assistance.