Tractel Tirak Blocstop BSO XE 1020 P User Manual (English)

Questions and Answers:

J
Jacob JonesAug 18, 2025
Why is my Tractel Industrial Equipment motor overheating?
- R
  Robert FordAug 18, 2025
  Your Tractel Industrial Equipment motor might be overheating due to several reasons: * The unit may be overloaded, in which case you should check the load and reduce it if necessary. * The voltage may be too high or too low; check the current consumption and compare it with the motor label specifications, also check the current and voltage. * The starting capacitor might still be activated because of a centrifugal switch defect. Check the current at the auxiliary winding in the control box when running the motor. For centrifugal switch repair contact the supplier. * There may be a crooked motor shaft, in which case contact the supplier. * The brake might not be correctly released; inspect the brake.
S
smithjasonAug 20, 2025
What to do if my Tractel Tirak Blocstop BSO XE 1020 P motor does not run at all?
- B
  brett91Aug 20, 2025
  If the motor of your Tractel Industrial Equipment does not run, it could be due to: * A power failure. Check the fuses, power cords, connections, and starting capacitor. * Incorrect wiring. Compare the wiring with the wiring diagram. * On a 3-phase motor, it could be stopped by the phase control relay. Check the wiring.
C
Cheryl MeyerAug 22, 2025
What to do if my Tractel Tirak Blocstop BSO XE 1020 P motor stalls under load?
- J
  Jesse SanchezAug 22, 2025
  If your Tractel Industrial Equipment motor stalls under load, it is likely due to low voltage. Check the voltage when the motor is running and use power cords with higher cross sections.
J
Joseph Curtis Jr.Aug 25, 2025
Why is my Tractel Tirak Blocstop BSO XE 1020 P motor making abnormal noises?
- D
  drewwalkerAug 26, 2025
  Abnormal motor noise in your Tractel Industrial Equipment can be caused by: * Electric parts. See causes/remedies above 1. to 5. (noise disappearing immediately, when stopping motor). * Mechanical parts. In this case, contact the supplier.
E
elizabethwilliamsAug 27, 2025
What to do if my Tractel Industrial Equipment motor does not start with a load?
- E
  Elizabeth BarnesAug 27, 2025
  If the motor of your Tractel Industrial Equipment does not start with a load, the possible causes are: * Overload. Check the load and reduce it if necessary. * The brake is not released. Check the motor with the brake released by hand. Check the brake according to para. 5.1 (2), page 14. * The voltage is too low. Check the voltage when running the motor and use power cord(s) with a higher cross section. * Incorrect wiring. Compare the wiring with the wiring diagram.
J
jeffreythompsonAug 30, 2025
What to do if my Tractel Tirak Blocstop BSO XE 1020 P Industrial Equipment is overheating when running without load?
- N
  nguyenjonathanAug 30, 2025
  If your Tractel Industrial Equipment is overheating when running without a load, possible causes include: * Insufficient cooling. Clean the motor fan cover. * Incorrect wiring. Compare the wiring with the wiring diagram. * Voltage too high. Check the voltage and no-load current. * Short circuit in the coil. Contact the supplier.
G
gary10Sep 2, 2025
What to do if the wire rope does not move through my Tractel Industrial Equipment?
- J
  Joshua BallSep 2, 2025
  If the wire rope does not move through your Tractel Industrial Equipment, it is likely that damaged wire rope is jamming the hoist. WARNING: STOP OPERATIONS IMMEDIATELY! Continued operation might cause wire rope failure. Contact the supplier.
N
Nancy MasseySep 4, 2025
What to do if the brake does not open on my Tractel Industrial Equipment?
- D
  David WestSep 4, 2025
  If the brake on your Tractel Industrial Equipment does not open, and there is a lack of a “click” switch noise when starting or stopping the hoist, it could be due to: * A defective supply conductor, brake coil, or rectifier. Have the supply conductor, current passage in the brake coil, and rectifier checked by an electrician or qualified person. * A worn brake rotor. Contact the supplier.
M
Misty JonesSep 6, 2025
What to do if the BSO secondary brake automatically closes without apparent reason on my Tractel Tirak Blocstop BSO XE 1020 P Industrial Equipment?
- K
  kevinherringSep 6, 2025
  If the BSO secondary brake on your Tractel Industrial Equipment automatically closes without an apparent reason, it could be due to: * A mechanical defect; contact the supplier. * Oversized or damaged wire rope; check the wire rope and replace it if necessary.
J
Jacqueline MartinSep 9, 2025
What to do if the hoist goes up but not down with my Tractel Tirak Blocstop BSO XE 1020 P?
- J
  James HutchinsonSep 9, 2025
  If your Tractel Industrial Equipment hoist goes up but not down, the BSO secondary brake is likely closed because the primary wire rope has run out or has failed. WARNING: STOP DOWNWARD TRAVEL! Proceed according para. 5.4, (3), page 16.