To Next PageTo Next Page
Need help?Do you have a question about the Trane THC067E and is the answer not in the manual?
General| Model Number | THC067E |
|---|---|
| Category | Air Conditioner |
| Brand | Trane |
| Cooling Capacity | 67, 000 BTU/h |
| Energy Efficiency Ratio (EER) | 11.5 |
| Refrigerant Type | R-410A |
| Voltage | 208/230V |
| Phase | 1 |
| Compressor Type | Scroll |
Explains the coding system for unit model numbers.
Provides explanations and clarifications for various digits in the model number.
Details the coding system specific to the 17 Plus Precedent series models.
Offers explanations for digits used in the 17 Plus model number designation.
Steps for inspecting the unit upon arrival to check for damage and verify data.
Precautions to prevent condensate formation during unit storage.
Details the data found on the unit's nameplate.
Overview of basic input devices used within the RTRM network.
Explains the function and operation of the clogged filter switch.
Details the function and operation of the condensate overflow switch.
Describes the operation of the low-pressure control for compressor protection.
Details the operation of the high-pressure control for compressor protection.
Describes different models of Zone Sensor Modules and their features.
Explains the function of the smoke detector for unit shutdown.
Illustrates minimum operating and service clearances for unit installation.
Covers safety warnings and preparations before installation begins.
Details requirements for constructing unit foundations and supports.
Illustrates supply and return air openings for downflow configuration.
Guidelines for verifying and installing roof curbs for downflow units.
Instructions and safety warnings for rigging and lifting the unit.
Checklist summarizing key steps for successful unit installation.
Step-by-step instructions for converting 3-5 ton units to horizontal discharge.
Step-by-step instructions for converting 6-10 ton units to horizontal discharge.
Procedure for replacing the TCO-A limit control for horizontal duct configuration.
Instructions for converting the return air smoke detector for horizontal discharge.
Safety warnings and requirements for main unit power connections.
Methods for converting the condensate drain to front or through-base.
Guidelines for correctly sizing and installing supply power wiring.
Layout and conductor requirements for control options.
Wiring guidelines for 24 VAC controls, including conductor sizing.
Procedure to measure and calculate voltage imbalance in three-phase power.
How to check and correct electrical phasing for three-phase motors.
Explains the importance of crankcase heaters for compressor oil temperature.
Details self-diagnostic checks and test procedures for ReliaTel controls.
Guides for testing electromechanical controls and their components.
Procedures for verifying and adjusting system airflow for proper unit operation.
Airflow verification for units with 5-tap direct drive indoor fans.
Airflow verification for units with belt drive indoor fans.
Airflow verification for units with constant CFM direct drive indoor fans.
Airflow adjustment for 17 Plus units using constant CFM direct drive fans.
Control strategies for Variable Air Volume applications.
How the RTRM maintains selectable supply air temperature.
Control of supply duct static pressure using a transducer.
How supply air temperature can be reset based on various conditions.
Procedures for starting up the economizer system.
Steps for starting compressors, including safety checks and pressure monitoring.
How to operate the dehumidification option and monitor settings.
Final checks and procedures before leaving the unit after installation and start-up.
Detailed instructions for adjusting fan belt tension on belt drive units.
General tasks for monthly unit maintenance.
Specific maintenance checks and procedures for the cooling season.
Guidelines for cleaning evaporator and condenser coils for efficiency.
Specific notice and method for cleaning microchannel condenser coils.
Handling and cleaning procedures for RTPF coils, including safety warnings.
General annual maintenance tasks and recording data.
Steps for checking unit diagnostics and system status via the RTRM.
Methods for checking system status using LED indicators on the ZSM.
Identifies potential causes for cooling failures and checks required.
Identifies potential causes for service failures and checks required.
Explains the function of the ZTS service LED as a generic indicator.
Describes the function and indication of the clogged filter switch.
Describes the function and indication of the fan failure switch.
Procedures for testing the zone temperature sensor and its components.
How to test the relative humidity sensor's mA output signal.
Testing serial communication voltage and sensor function.
Troubleshooting the Economizer Control Actuator using LED indicators.
Troubleshooting steps for electromechanical controls.
Tests to diagnose problems within the system economizer operation.
Details the limited warranty for residential electric air conditioners.
Details the limited warranty for commercial electric air conditioners.
