Transition Networks SGFEB1013-120 - Installation: Switches and Settings; Six-Position Switch Configuration; Twisted-Pair Connection Settings

2
SGFEB10xx-12x
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
SGFEB1029-120
RJ-45
100 m (328 ft)
SC, 1310nm TX/1550 nm RX single mode
20 km (12.4 miles)
SGFEB1029-121
RJ-45
100 m (328 ft)
SC, 1550nm TX/1310 nm RX single mode
20 km (12.4 miles)
Install SGFEB1029-120 and SGFEB1029-121 single-fiber optic in
the same network where one is the local converter and the other is
the remote converter.
SGFEB1029-122
RJ-45
100 m (328 ft)
SC, 1310 nm TX/1550 nm RX single mode
40 km (24.9 miles)
SGFEB1029-123
RJ-45
100 m (328 ft)
SC, 1550nm TX/1310nm RX single mode
40 km (24.9 miles)
Install SGFEB1029-122 and SGFEB1029-123 single-fiber optic in
the same network where one is the local converter and the other is
the remote converter.
SGFEB1029-124
RJ-45
100 m (328 ft)
SC, 1510 nm TX/1590 nm RX single mode
80 km (49.6 miles)
SGFEB1029-125
RJ-45
100 m (328 ft)
SC, 1590 nm TX/1510 nm RX single mode
80 km (49.6 miles)
Install SGFEB1029-124 and SGFEB1029-125 single-fiber optic in
the same network where one is the local converter and the other is
the remote converter.
Part Number Port 1 - Copper
10/100/1000Base-TX
Port 2 - Duplex Fiber-Optic
1000Base LX
Wide Input (18-72VDC) Power Supplies
SPS-1872-PS or sps-1872-SA
Mounting Options
E-MCR-04
12-Slot Media Converter Rack
WMBD
DIN Rail Mount Bracket 5.0” (127 mm)
WMBL
Wall Mount Bracket 4.0” (102 mm)
RMS19-SA4-01
4-Slot Media Converter Shelf
Optional accessories
SGFEB10xx-12x
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
3
Installation
CAUTION: Wear a grounding device and observe electrostatic discharge precautions
when setting or installing the media converter. Failure to observe this caution could
result in damage to, and subsequent failure of, the media converter slide-in-module.
Six-position switch
The six-position switch is located on the circuit board of the media converter. Use a
small, flat-blade screwdriver (or a similar device) to set the switch according to the
site the requirements (see the drawing below).
TP Speed: UP =100 Mbs, Down = 10 Mbs (Note 1)
TP Auto-Negotiation: UP = Enabled, Down = Disabled
TP Duplex: UP = Full, Down = Half (Note 1)
LPT: UP = Enabled, Down = Disabled
Unused
SW Position Up
SW Position Down
Unused
123456
Note 1: Only use when Autonegotiation is disabled.
1. Twisted-Pair Auto-Negotiation
UP Enable Auto-Negotiation for the copper connection.
DOWN Disable Auto-Negotiation for the copper connection.
2. Twisted-Pair 10Mbs/100Mbs
UP Set copper connection speed to 100Mbs.
DOWN Set copper connection speed to 10Mbs.
3. Twisted-Pair Full/Half Duplex
UP Operate in full-duplex mode.
DOWN Operate in half-duplex mode of the attached device.
4. Link Pass-Through (LPT)
UP Enable Link Pass-Through
DOWN Disable Link Pass-Through.
5. Not used
6. Not used