Transition Networks SSDTF1011-105 User Manual

Installation . . . . . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . .9
Cable Specifications . . . . . . . . . .10
Technical Specifications . . . . . . .12
Troubleshooting . . . . . . . . . . . . .13
Compliance Information . . . . . . .16
* Typical maximum cable distance. (Actual
distance is dependent upon the physical
characteristics of the network.)
Note: The SSDTF10xx-10x requires a CSU
between the converter and the Public
Telephone Network.
SSDTF1027-105
RJ-45
1.5 km (5,000 feet)*
ST, 1300 nm multimode
5 km (3.1 miles)*
Part Number Port One - Copper Port Two - Duplex Fiber-Optic
SSDTF1011-105
RJ-45
1.5 km (5,000 feet)*
ST, 850 nm multimode
2 km (1.2 miles)*
SSDTF1012-105
RJ-45
1.5 km (5,000 feet)*
ST, 1310 nm single mode
8 km (4.8 miles)*
SSDTF1013-105
RJ-45
1.5 km (5,000 feet)*
SC, 850 nm multimode
2 km (1.2 miles)*
SSDTF1014-105
RJ-45
1.5 km (5,000 feet)*
SC, 1310 nm single mode
20 km (12.4 miles)*
SSDTF1015-105
RJ-45
1.5 km (5,000 feet)*
SC, 1310 nm single mode
40 km (24.8 miles)*
SSDTF1016-105
RJ-45
1.5 km (5,000 feet)*
SC, 1310 nm single mode
60 km (37.3 miles)*
SSDTF1017-105
RJ-45
1.5 km (5,000 feet)*
SC, 1550 nm single mode
80 km (49.7 miles)*
SSDTF1018-105
RJ-45
1.5 km (5,000 feet)*
MT-RJ, 1300 nm multimode
2 km (1.2 miles)*
SSDTF1022-105
RJ-45
1.5 km (5,000 feet)*
ST, 1310 nm single mode
15 km (9.3 miles)*
SSDTF1025-105
RJ-45
1.5 km (5,000 feet)*
MT-RJ, 1310 nm single mode
20 km (12.4 miles)*
User’s Guide
SSDTF10xx-10x
Stand-Alone Media Converter
• T1 / E1 with Remote Management
• Copper to Fiber
Transition Networks SSDTF10xx-10x series media
converters encode and decode T1 or E1 twisted-pair
copper signals over fiber optic cable to extend the
distance and transmission reliability of high-speed
T1 or E1 data traffic. The device is framing independent (as ESF vs. D4) and supports all
common line codes (e.g., AMI, B8ZS, HDB3).
The SSDTF10xx-10x is designed to be installed in pairs. For example, install one
SSDTF1011-105 as the “local” media converter and another SSDTF1011-105 as the
“remote” media converter.

Transition Networks SSDTF1011-105 Specifications

General

Device Type	Media Converter
Power Supply	5V DC, 1A
Number of Ports	2
Maximum Distance Supported (Twisted Pair)	100 m
Ethernet Ports	1
Connector	RJ-45, SC
Operating Temperature	0°C to 50°C
Fiber Ports	1
Twisted Pair Ports	1
Fiber Type	Multimode