What does 'FAN FAULT' mean on my Tripp Lite SmartOnline SU1000RTXLCD2U UPS and how to fix it?
If your Tripp Lite UPS displays 'FAN FAULT', there may be a problem with the fan. Check if something is blocking the fan's rotation and remove it. If the problem continues, contact Tripp Lite for assistance.
What to do if my Tripp Lite SmartOnline SU1000RTXLCD2U shows OVER TEMP?
The Tripp Lite UPS may display 'OVER TEMP' because its internal temperature is too high. Ensure adequate space around the UPS for air circulation near the vents and verify the fan is functioning correctly. Also, make sure the UPS is operating within a 0-40°C / 32-104°F environment.
How to fix OVERLOAD on my Tripp Lite SmartOnline SU1000RTXLCD2U?
The 'OVERLOAD' error on your Tripp Lite UPS indicates that the connected load is too high. Reduce the amount of equipment plugged into the UPS to resolve this issue.
What to do if Tripp Lite SmartOnline SU1000RTXLCD2U displays O/P SHORT?
The 'O/P SHORT' error on your Tripp Lite UPS means there is a short circuit on the output. Disconnect the devices connected to the UPS one by one to find and remove the device causing the short circuit.
What causes FAN FAULT on Tripp Lite UPS?
A 'FAN FAULT' on your Tripp Lite UPS suggests the fan isn't working correctly. Check for any obstructions that may be preventing the fan from rotating, and remove them. If the problem continues, contact Tripp Lite for assistance.
What does 'I/P OVER CURRENT' mean on my Tripp Lite UPS?
If your Tripp Lite UPS displays 'I/P OVER CURRENT', there are issues with the PFC or INV circuit. If the problem persists, contact Tripp Lite for assistance.
What does '+/-DC BUS HIGH/LOW' mean on my Tripp Lite SmartOnline SU1000RTXLCD2U UPS?
If your Tripp Lite UPS displays '+/-DC BUS HIGH/LOW', the internal DC bus voltage is either too high or too low. If the problem persists, contact Tripp Lite for assistance.
What does 'BUS OVP' mean on my Tripp Lite SmartOnline SU1000RTXLCD2U UPS?
If your Tripp Lite UPS displays 'BUS OVP', the internal DC bus voltage is too high. If the problem persists, contact Tripp Lite for assistance.
What to do if my Tripp Lite SmartOnline SU1000RTXLCD2U displays 'O/P SHORT'?
If your Tripp Lite UPS displays 'O/P SHORT', it means the UPS output has a short circuit. Disconnect the connected devices, find the cause of the short circuit, and remove it from the UPS output.
How to fix an 'OVER TEMP' error on a Tripp Lite SmartOnline SU1000RTXLCD2U UPS?
If your Tripp Lite UPS displays an 'OVER TEMP' warning, it means the internal temperature is too high. Ensure there's enough space around the UPS for air circulation and that the fan is working. The UPS should be in an environment between 0-40°C / 32-104°F.
General| Output Power Capacity | 900 W |
|---|---|
| Form Factor | 2U Rackmount |
| Number of Outlets | 8 |
| Input Frequency | 50/60 Hz |
| Output Frequency | 50/60 Hz |
| Network Management | Optional SNMP/Web card |
| Waveform Type | Sine Wave |
| Operating Temperature | 32 to 104°F (0 to 40°C) |
| Power Rating | 1000 VA |
| Output Capacity | 1000 VA |
| Input Voltage | 120V |
| Output Voltage | 120V |
| Battery Type | Sealed Lead Acid |
| Typical Backup Time (Half Load) | 14.5 min |
| Outlets | 8 NEMA 5-15R |
| Communication Ports | USB |
| Transfer Time | 4ms typical |
| Operating Humidity | 0 to 95% (non-condensing) |
| Certifications | UL1778, cUL, FCC Part 15 Class A |
| Warranty | 2-year limited warranty |
To Next Page
