EasyManua.ls Logo

Troy-Bilt 060 series - User Manual

Troy-Bilt 060 series
40 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
TROY BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
4/23/2007
FORM NO. 769-00835D
Safety • Assembly • Operation • Maintenance • Troubleshooting • Parts Lists • Warranty
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
PRINTED IN U.S.A.
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
IMPORTANT
OPERATOR’S MANUAL
Yard Vacuum/Chipper/Shredder with Vacuum/Hose
Model Series 060

Table of Contents

Questions and Answers

  • A
    Alexandria Keith MDJul 26, 2025
    What to do if Troy-Bilt Chippers/Shredders unit does not discharge?
    • A
      Anne WilliamsJul 26, 2025
      If your Troy-Bilt Chippers/Shredders unit does not discharge, immediately stop the engine and disconnect the spark plug wire. Then, clean the flail screen and the inside of the discharge opening to remove any clogs. Also, stop the engine and disconnect the spark plug wire to remove any foreign object lodged in the impeller. Ensure the engine is running at full throttle and that the vacuum bag is not full; empty the bag if necessary.
  • M
    michellejacksonAug 1, 2025
    Why Troy-Bilt 060 engine runs erratic?
    • T
      Tony RobinsonAug 1, 2025
      If your Troy-Bilt Chippers/Shredders engine runs erratically, begin by checking the spark plug wire to ensure it is securely connected and tightened. If your unit is equipped with a choke, make sure it is not running on CHOKE; move the choke lever to the OFF position. Inspect the fuel line for blockages and use clean, fresh gasoline. Ensure the engine is always running at full throttle. Drain the fuel tank and refill it with fresh fuel to eliminate any water or dirt in the fuel system. For a dirty air cleaner or carburetor issues, consult an authorized service dealer.
  • K
    Kelly MccannAug 7, 2025
    Why Troy-Bilt 060 rate of discharge slows?
    • K
      Karen McmillanAug 7, 2025
      If the rate of discharge slows considerably or the composition of discharged material changes in your Troy-Bilt Chippers/Shredders, ensure the engine is running at full throttle. If the issue persists, the chipper blade may be dull and need replacement, or consult your authorized service dealer.
  • S
    Sarah ValentineAug 13, 2025
    Why Troy-Bilt 060 engine overheats?
    • A
      Alexander TuckerAug 13, 2025
      If your Troy-Bilt Chippers/Shredders engine overheats, start by checking the engine oil level and fill the crankcase with the proper oil if it's low. For a dirty air cleaner or carburetor issues, consult an authorized service dealer.
  • M
    moranjasonAug 19, 2025
    What causes occasional skips in Troy-Bilt Chippers/Shredders?
    • J
      Jessica HarveyAug 19, 2025
      If your Troy-Bilt Chippers/Shredders occasionally skips (hesitates) at high speed, remove the spark plug and adjust the gap. For carburetor idle mixture adjustments consult an authorized service dealer.

Summary

Safety Labels

Safety Warnings and Labels

Explains DANGER and WARNING labels found on the machine for user safety.

Height Adjustment Controls

Describes the front wheel and vacuum nozzle height adjustment lever.

Safe Operation Practices

Operator Training Requirements

Details essential operator training and familiarization steps for safe use.

Pre-Operation Preparation

Lists crucial checks and safety measures before starting the machine.

General Operation Guidelines

Outlines safe practices and precautions to follow during machine operation.

Maintenance and Storage Safety

Provides safety rules and guidelines for unit upkeep and storage.

Setting Up Your Chipper Shredder Vacuum

Attaching the Handles

Provides step-by-step instructions for assembling the upper and lower handles.

Connecting the Hose Assembly

Guides the user through attaching the vacuum hose to the machine.

Securing the Collection Bag

Instructions for properly attaching the debris collection bag.

Operating Your Chipper Shredder Vacuum

Controls and Features Overview

Identifies and explains the machine's controls and key components.

Fueling and Oiling Procedures

Instructions for safely filling the fuel tank and checking engine oil.

Starting and Stopping the Engine

Details the steps for safely starting and shutting down the engine.

Emptying the Collection Bag

Procedures for removing and emptying the debris collection bag.

Using The Nozzle Vacuum

How to use the nozzle for vacuuming yard waste.

Using The Hose Assembly

Guidelines for vacuuming hard-to-reach areas with the hose.

Nozzle Height Adjustment

Adjusting the nozzle height for different ground conditions.

Maintaining Your Chipper Shredder Vacuum

General Maintenance Recommendations

Basic advice for keeping the unit in optimal working condition.

Lubrication Points

Details specific points requiring lubrication and frequency.

Equipment Cleaning

Procedures for cleaning the chipper shredder vacuum after use.

Engine Maintenance

Specific care and checks for the engine, referencing its manual.

Flail Screen Cleaning

Instructions on how to remove and clean the flail screen.

Chipper Blade Maintenance

Guide for sharpening or replacing the chipper blade.

Seasonal Storage

Recommendations for storing the unit during the off-season.

Troubleshooting

Engine Starting Issues

Common problems and solutions for engine failure to start.

Engine Performance Problems

Remedies for erratic engine running, overheating, or hesitation.

Operational Issues

Solutions for excessive vibration, discharge problems, or slow performance.

Parts List

Component Identification

Lists components with part numbers and descriptions from the initial section.

Detailed Parts Listing

Continues the comprehensive list of replacement parts and their numbers.

Manufacturers Limited Warranty

Warranty Coverage and Terms

Details what the warranty covers, its duration, and conditions.

Obtaining Warranty Service

Explains the process and requirements for claiming warranty service.

Warranty Exclusions

Lists conditions, parts, and situations not covered by the warranty.

Troy-Bilt 060 series Specifications

General IconGeneral
BrandTroy-Bilt
Model060 series
CategoryChippers/Shredders
LanguageEnglish

Related product manuals