To Next PageTo Next PageWhat to do if True Merchandiser compressor runs but doesn't refrigerate?
If your True Merchandiser's compressor is running but not refrigerating, check the refrigerant charge, suction pressure, and discharge pressure. If the suction pressure is high and the evaporator and condenser are working correctly, check the compressor amperage draw.
Why does my True Merchandiser compressor start but trip the overload protector?
If the motor compressor in your True Merchandiser starts but repeatedly trips the overload protector, begin by checking the compressor's suction and discharge pressures while it's running. Also, check the line voltage at the motor terminals during operation and verify the amperage draw. If all operating conditions, voltage, and amperage are within normal limits, the motor protector itself may be defective and should be replaced. However, if the compressor runs excessively hot or the amperage draw is too high, it may indicate internal damage, requiring compressor replacement.
How to fix a True Merchandiser coil defrost heater trip?
If the coil defrost heater in your True Merchandiser is tripping, use an ohmmeter to check the heater for continuity. If the heater is defective, cut the bale wires holding it to the coil, remove the old heater, and replace it with a new one using the provided bale wires.
How to resolve a True Merchandiser drain tube heater trip?
If the drain tube heater in your True Merchandiser is tripping, use an ohmmeter to check the heater. If it's defective, disconnect the drain tube from the rigid plastic drain, bend the evaporator drain pan tabs to expose the flexible heater, pull the heater out of the plastic drain tube, and replace it. Then, connect the heater to the electrical circuit in the evaporator compartment.
How to troubleshoot a True Merchandiser compressor that won't run?
If the compressor on your True Merchandiser isn't running, start by checking for voltage at the compressor terminals. If there's no voltage, trace the wiring from the compressor back to the power supply to find any breaks in the circuit. If voltage is present but the compressor still doesn't run, measure the voltage at the terminals while trying to start the compressor. If it's below 90% of the nameplate voltage, inadequate torque might be the issue. Inspect wire sizes, connections, and the power supply. For single-phase compressors, a faulty capacitor or relay could be the cause; check the relay for damage. If the correct voltage is available but no current is drawn, disconnect all wires and check the motor windings for continuity. Also, check for a ground between the common terminal and ...
Essential safety measures for operating and installing the refrigerator.
Procedures for safe disposal and preventing child entrapment risks.
Guidelines for safe electrical connection, grounding, and avoiding extension cords.
Procedures for uncrating the unit and initial setup.
Instructions for properly leveling the refrigerator for optimal operation.
Guide for securely installing optional legs or castors.
Detailed steps for operating, removing, and reinstalling slide doors.
Table showing wire gauge requirements for electrical circuits.
Guidelines for electrical connections and sealing the cabinet to the floor.
Introduction to the LAE electronic control for temperature management.
Managing LAE controller features like locking, lights, and set points.
Specific procedures for adjusting temperature controls for high altitude.
Operation and adjustment of the Grasslin defrost time clock.
Procedures for cleaning the condenser coil for optimal performance and longevity.
Steps for safely replacing interior light bulbs in the unit.
Guidelines for cleaning and maintaining stainless steel surfaces to prevent corrosion.
Details on parts, labor, compressor warranty, exclusions, and claim procedures.
Essential safety measures for operating and installing the refrigerator.
Procedures for safe disposal and preventing child entrapment risks.
Guidelines for safe electrical connection, grounding, and avoiding extension cords.
Procedures for uncrating the unit and initial setup.
Instructions for properly leveling the refrigerator for optimal operation.
Guide for securely installing optional legs or castors.
Detailed steps for operating, removing, and reinstalling slide doors.
Table showing wire gauge requirements for electrical circuits.
Guidelines for electrical connections and sealing the cabinet to the floor.
Introduction to the LAE electronic control for temperature management.
Managing LAE controller features like locking, lights, and set points.
Specific procedures for adjusting temperature controls for high altitude.
Operation and adjustment of the Grasslin defrost time clock.
Procedures for cleaning the condenser coil for optimal performance and longevity.
Steps for safely replacing interior light bulbs in the unit.
Guidelines for cleaning and maintaining stainless steel surfaces to prevent corrosion.
Details on parts, labor, compressor warranty, exclusions, and claim procedures.
General| Brand | True |
|---|---|
| Model | GDM-69 |
| Category | Merchandiser |
| Language | English |
