Truma Mover smart M - User Manual

Questions and Answers

C
corey85Aug 14, 2025
What to do if Truma Automobile Accessories mover is not responding to the remote control?
- A
  Abigail ScottAug 14, 2025
  If your Truma Automobile Accessories mover isn't responding to the remote control, or is responding intermittently, it could be due to a low battery. First, check the battery and battery contacts of the remote control. If needed, replace the battery or clean the battery contacts. Another cause could be a low battery in the mover itself, indicated by a flashing green LED on the control unit. In this case, check, charge, or replace the mover's battery.
J
justin01Aug 17, 2025
What to do if Truma Automobile Accessories mover does not engage on one side?
- S
  Scott KnappAug 17, 2025
  If the Truma Automobile Accessories mover does not engage on one side (only Mover smart A), ensure that when disengaging the mover, the power supply isn't interrupted, and the remote control isn't switched off. The process is complete only after the indicator on the remote control stops flashing. You can also manually engage the Mover with the socket wrench by approximately two clockwise resolutions, then try engaging the Mover once again.
S
stevendixonAug 20, 2025
Why is my Truma Automobile Accessories manoeuvring system remote not working?
- W
  wleeAug 20, 2025
  If your Truma Automobile Accessories manoeuvring system isn't responding to the remote or is only working intermittently, the issue might be a weak battery in the remote. Check the battery and battery contacts of the remote control. If the red LEDs are flashing, replace the battery and clean the battery contacts if needed. Alternatively, the manoeuvring system's battery might be low. If the green LED on the control unit flashes, check the manoeuvring system's battery and charge or replace it if necessary.
M
Mandy JohnsonAug 25, 2025
What to do if Truma Automobile Accessories manoeuvring system is not working and red LED is flashing?
- T
  tvargasAug 25, 2025
  If your Truma Automobile Accessories manoeuvring system isn't working and the red LED on the control unit is flashing, the control unit may be overheated. To resolve this, interrupt the power supply using the battery cut-off switch and remove the key. Allow the control unit to cool down for at least 20 minutes before restarting the manoeuvring system.
J
Jason GibsonAug 27, 2025
How to fix Truma Automobile Accessories manoeuvring system not working?
- S
  Sandra TaylorAug 27, 2025
  If your Truma Automobile Accessories manoeuvring system isn't working, check the power supply, ensuring the green LED on the control unit is lit. Replace any defective fuse in the battery connection cable of the manoeuvring system only with an original Truma spare part (part no. 60040-00169). If this doesn't solve the problem, interrupt the power supply for at least 20 seconds, then restore it. The green LED on the control unit should then light up.
T
Todd WhiteAug 30, 2025
Why is my Truma Mover smart M Automobile Accessories mover not working?
- A
  Andres Taylor MDAug 31, 2025
  If your Truma Automobile Accessories mover isn't working, begin by checking the power supply; the green LED on the control unit should be lit. If it’s still not working, the fuse in the mover’s battery connector cable may be faulty and should be replaced with an original Truma spare part. As an additional step, you can interrupt the power supply for at least 20 seconds and then re-establish it to see if the green LED on the control unit illuminates.
G
Gloria CrawfordSep 2, 2025
What to do if the red LED on the Truma Mover smart M mover control unit is flashing?
- S
  Samantha LunaSep 2, 2025
  If the red LED on the control unit of your Truma Automobile Accessories mover is flashing, it indicates that the control unit has overheated. To resolve this, interrupt the power supply using the battery cut-off switch and remove the key. Allow the control unit to cool down for at least 20 minutes before restarting the mover.
K
Kelly SandovalSep 6, 2025
What to do if Truma Mover smart M drive roller slides down on the wheel?
- A
  Angel JonesSep 6, 2025
  If the drive roller on your Truma Automobile Accessories is sliding down on the wheel, first check the tire pressure and adjust it if necessary. Also, inspect the tire profile and replace the tires if needed. As a final step, disengage the mover and measure the distance between the tires and drive roller, ensuring it is 20 mm.
R
Randall SparksSep 10, 2025
What to do if the drive roller is sliding off tyre on my Truma Automobile Accessories?
- C
  Carmen AlvaradoSep 10, 2025
  If the drive roller is sliding off the tyre on your Truma Automobile Accessories, there are a few things you can check. First, check the tyre pressure and adjust it if necessary. Next, inspect the tyre tread and replace the tyres if needed. Finally, disengage the manoeuvring system and measure the gap between the tyres and the drive roller, which should be 20 mm.