TUG Technologies 663 - Ramp Safety in Aircraft Handling; General Ramp Safety; Danger Areas; Equipment Specifications

CD397-Oper Introduction - 1 - vii
Mobile Belt Loader Model 660
Operation Manual
Introduction
2.1.3 Maneuvering Controls.......................................................................Operation - 2 - 15
2.1.4 Conveyor Controls ............................................................................Operation - 2 - 16
2.1.5 Electrical Supply ...............................................................................Operation - 2 - 17
2.1.6 Preliminary Checks ...........................................................................Operation - 2 - 17
2.1.7 Maneuvering Procedures..................................................................Operation - 2 - 18
2.1.7.1 Engine Start Procedure (Gas)..................................................Operation - 2 - 18
2.1.7.2 Engine Start (Diesel)................................................................Operation - 2 - 19
2.1.7.3 Release parking brake. ............................................................Operation - 2 - 19
2.1.7.4 Transmission Drive (FWD/REV) Selection...............................Operation - 2 - 19
2.1.7.5 Depress foot throttle.................................................................Operation - 2 - 20
2.1.7.6 Maneuver vehicle with steering wheel. ....................................Operation - 2 - 20
2.1.7.7 Maneuvering the baggage loader around the aircraft ..............Operation - 2 - 21
2.1.8 Belt Loader Towing Instructions........................................................Operation - 2 - 21
2.1.8.1 Towing Requirements ..............................................................Operation - 2 - 21
2.1.9 Conveyor Safety Props .....................................................................Operation - 2 - 23
2.2 IATA...........................................................................................................Operation - 2 - 24
2.3 SAE............................................................................................................Operation - 2 - 24
2.4 ISO EMC Evaluation..................................................................................Operation - 2 - 24
2.5 ISO Product Safety Evaluation ..................................................................Operation - 2 - 25
2.6 Locations of Technical Construction Files .................................................Operation - 2 - 25
Section 3: Specifications ........................................................................... Operation - 3 - 27
3.1 General Specifications of the 660..............................................................Operation - 3 - 27
3.1.1 Dimensions .......................................................................................Operation - 3 - 27
3.2 Torque Values............................................................................................Operation - 3 - 28
3.2.1 Metric Fasteners ...............................................................................Operation - 3 - 28
3.2.2 Graded Bolts .....................................................................................Operation - 3 - 29
3.3 Performance ..............................................................................................Operation - 3 - 31
3.3.1 Specifications....................................................................................Operation - 3 - 31
3.3.2 Environmental Operating Limits........................................................Operation - 3 - 32
3.3.3 Environmental Vibration Information.................................................Operation - 3 - 32
3.3.4 Environmental Sound Information.....................................................Operation - 3 - 32
3.4 Engines......................................................................................................Operation - 3 - 35
3.4.1 Gasoline............................................................................................Operation - 3 - 35
3.4.1.1 Ford MSG-425 2.5L .................................................................Operation - 3 - 35
3.4.2 Diesel ................................................................................................Operation - 3 - 35
3.4.2.1 Deutz D2.9L .............................................................................Operation - 3 - 35
3.5 Transmission..............................................................................................Operation - 3 - 36
3.5.1 Gear Ratios.......................................................................................Operation - 3 - 36
3.6 Standard Conveyor Heights and Angles....................................................Operation - 3 - 37
3.7 Compatible Aircraft ....................................................................................Operation - 3 - 38
3.8 Fluids .........................................................................................................Operation - 3 - 42
3.9 Coolant.......................................................................................................Operation - 3 - 43
3.10 Recommended Spare Parts.....................................................................Operation - 3 - 43
3.11 Safety Features........................................................................................Operation - 3 - 44
3.11.1 Shifter / Parking Brake Safety.........................................................Operation - 3 - 44
3.11.2 Shifter Guard...................................................................................Operation - 3 - 44
3.11.3 Neutral Safety Start Switch .............................................................Operation - 3 - 44
3.11.4 Anti-Restart Ignition Switch.............................................................Operation - 3 - 44
3.11.5 Engine Control Module (ECM) Starter Protection ...........................Operation - 3 - 45
3.11.5.1 Ford 2.5L................................................................................Operation - 3 - 45