EasyManuals Logo

ULTIMATE SPEED UPK 10 A1 User Manual

ULTIMATE SPEED UPK 10 A1
33 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #13 background imageLoading...
Page #13 background image
GB / IE / NI 13
Switching on/off:
Switching the device on: move the on/off
switch for the power bank with compressor
8
to
the ‘On’ position�
Switching the compressor on: move the on/
off switch for the compressor
2
to ‘I’�
When the right filling pressure has been
achieved, switch the device off: move the on/off
switch for the compressor
2
to ‘0’�
Move the on/off switch for the power bank
with compressor
8
to the ‘Off’ position�
Disconnecting the connecting valve:
Connection without a valve adapter
13
:
Open the clamp lever
12
on the connecting
valve
15
by pressing the clamp lever
12
away
from the air hose
14
and then pull this off the
valve on the inflatable item�
Connecting valve
15
with valve adapter
13
: Pull the valve adapter off the connecting
valve on the inflatable item� Open the clamp
lever
12
on the connecting valve
15
by pressing
the clamp lever
12
away from the air hose
14
and then removing the valve adapter
Please note: When disconnecting the connect-
ing valve
15
, air can escape from the valve on
the inflatable item� Ensure that you remove the
connecting valve
15
as quickly as possible�
The pressure gauge is not trade-approved�
Accordingly, after pumping up inflatable items
where the wrong pressure could be dangerous
(e�g� vehicle tyres), always check the pressure at
a service point with a trade-approved device�
Tips for use
The device is not intended for continuous oper-
ation� The device was designed to create air
pressure – not an air flow
Please do not use the device for more than
7 minutes at a time on items with a large vol-
ume, to avoid overheating and damage to the
device� Then let the device cool down for at
least 15 minutes� We recommend first filling
a large-volume item with air, followed by then
using this device to generate the target pressure�
If you need a higher pressure than 3 bar for
a vehicle tyre, do not use the device for over
3 minutes at a time without stopping� Then let the
device cool down for at least 15 minutes�
Air pressure testing
Connect the connecting valve
15
(see ‘Using the
integrated compressor’)�
Read off the air pressure on the pressure gauge
display
3
Disconnect the connecting valve
15
again (see
‘Using the integrated compressor’)�
Please note: The pressure gauge is not
trade-approved�
Safety fuse
If the device becomes overloaded or malfunc-
tions, the safety fuse triggers to protect the
device�
Never install a fuse rated for a
higher trip current� Otherwise
there is a risk of fire!
• Switching on the lights
To switch on the lights
1
, press and hold
the on/off button on the power bank
4
for
3 seconds�
Press and hold the power button
4
again
for 3 seconds to turn the lights off again�
CAUTION! Do not look directly into
the lights
1
as this can damage your
eyes�
Please note: It is not possible to turn on the
lights while the power bank with compressor
6
is charging�
• Using the jumpstart feature
Check the charge level of the power bank with
compressor
6
� Check that at least 3 indicator
lights
5
are illuminated�
Connect the jumper cable
11
to the vehicle
jumpstart outlet
7
Connect the red crocodile clip to the positive
terminal on the car battery
Using the device

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the ULTIMATE SPEED UPK 10 A1 and is the answer not in the manual?

ULTIMATE SPEED UPK 10 A1 Specifications

General IconGeneral
BrandULTIMATE SPEED
ModelUPK 10 A1
CategoryAccessories
LanguageEnglish

Related product manuals