What to do if my Uniden PRO505XL won’t turn on?
If your Uniden Radio won’t turn on, make sure to check the radio’s power cord and all connections. Also, check the fuse in the radio’s power cord. Finally, verify your vehicle’s electrical system is functioning correctly.
How to fix poor reception on Uniden Radio?
To improve poor reception on your Uniden Radio, try adjusting the squelch level. Also, check the antenna, cable, and connectors for any issues. Lastly, verify the operation mode of the radio is set correctly.
Why is the transmission weak on my Uniden PRO505XL Radio?
To address weak transmission on your Uniden Radio, check the antenna, cable, and connectors for any issues. Also, check the antenna grounding and look for corrosion on the connectors.
How to reduce background noise on Uniden PRO505XL?
To eliminate background noise on your Uniden Radio, try adjusting the squelch level.
What to do if PA won’t broadcast on Uniden PRO505XL Radio?
If your Uniden Radio's PA won’t broadcast, ensure the CB/PA toggle is set to PA. Also, check that the microphone’s PTT button is pressed when you talk.
General| Maximum range | - m |
|---|---|
| Operating frequency | 26.965 - 27.405 MHz |
Weight and Dimensions| Weight | 1000 g |
|---|---|
| Dimensions (WxDxH) | 123.8 x 168 x 41 mm |
Lists essential items included with the scanner for setup and operation.
Explains legal aspects of using a scanner and prohibited transmissions.
Allows searching preset frequencies in specific bands like marine, fire/police, and aircraft.
Enhances readability in low-light conditions for the scanner's display.
Enables skipping specific channels or frequencies during scanning or searching.
Organizes up to 200 channels into 10 banks for easier identification.
Displays weather events for selected counties using SAME/FIPS codes.
Retains stored frequencies in memory for an extended period.
Adds a 2-second delay after a transmission to hear replies.
Allows checking a specific channel every 2 seconds during scanning.
Enables transferring programmed data to another scanner.
Allows connection of an external antenna for improved signal reception.
Explains frequency as a signal waveband and lists supported bands.
Explains channels as storage for frequencies and banks for grouping channels.
Instructions for attaching the included telescopic antenna.
Guidelines for connecting an external antenna, including cable types and safety.
How to connect external audio devices to the scanner.
Recommendations for protecting hearing while using the scanner.
Steps for connecting power and safely turning on the device.
Instructions to enable or disable audible key press tones.
Explains the meaning of indicators and text on the scanner's display.
Details the various messages and codes displayed on the scanner screen.
Explains specific messages related to scanner banks like VHF, UHF, and HAM.
Describes the function of each button on the scanner's keypad.
Details the use of number keys and function keys like DELAY, ENT, L/O, TUNE, and PGM.
Instructions to load 153 preprogrammed frequencies into the scanner.
Step-by-step guide to entering custom frequencies into scanner channels.
How to upload/download data using PC software and a cable.
Transferring programmed data between WS1025 scanners using a cable.
How to perform a tune search, tuning up or down from a specified frequency.
How to search preset frequencies in service bands like marine, fire/police, and aircraft.
Steps to save discovered frequencies into scanner channel-storage banks.
Explains commands like PSE, /Delay, and L/O for controlling searches.
How to continuously scan through channels with stored frequencies.
Method to identify internal scanner signals that cause interference.
How to set a two-second delay to avoid missing replies during conversations.
How to program and activate a priority channel for frequent monitoring.
How to continuously monitor a specific channel without scanning.
Steps to prevent the scanner from stopping on unwanted channels or frequencies.
Procedures for reviewing and removing locked-out channels.
How to manage lock-outs within service bank searches.
Procedure to remove all lock-outs from a service bank.
Steps to remove a frequency that was stored in a scanner channel.
How to listen to local and regional weather forecasts broadcast by agencies.
Setting up the scanner to monitor for all weather alerts.
Using SAME/FIPS codes to receive alerts for particular geographic areas.
Steps to program the scanner to monitor weather channels for SAME alerts.
How the scanner monitors weather channels and responds to alerts based on FIPS codes.
Procedure to test the scanner's weather alert sounds and display indicators.
How to program and activate the feature to monitor Skywarn amateur radio frequencies.
Guidelines for cleaning, handling, and storing the scanner to prevent damage.
Steps to perform a factory reset if the scanner display locks up or malfunctions.
Explains preset frequency groups for marine, fire/police, aircraft, ham, FM, and weather.
Lists frequency ranges and steps for fire and police service banks.
Lists frequency ranges and steps for aircraft service banks.
Lists frequency ranges and steps for Ham radio service banks.
Lists frequency range and step for FM broadcast service banks.
Lists frequencies for dedicated weather channels.
Lists frequencies for marine channels, noting duplex transmission pairs.
Details frequency coverage, sensitivity, selectivity, IF frequencies, and audio output.
Covers dimensions, weight, operating temperature, and power requirements.
Explains FCC compliance for scanning receivers and measures to mitigate interference.
Details the one-year warranty against defects and conditions for voiding it.
Instructions for returning the scanner for repair or replacement during the warranty period.
Explains conditions and fees for service outside the warranty period.
Provides contact information for inquiries and service during or after the warranty period.
Important safety warning regarding antenna installation and transmission distance.
Information on the CB license requirement and FCC regulations.
How to get answers and support from Uniden.
Lists items expected to be in the radio's package.
Identifies and describes the function of controls on the front of the radio.
Identifies and describes ports on the back of the radio, like antenna and power.
Explains how to use the microphone for transmitting and speaking.
Steps for physically connecting the microphone to the radio.
Instructions for connecting the radio to a 12-volt DC power source.
Guidance on choosing a location and mounting the radio securely.
Instructions and warnings for connecting an external CB antenna.
How to connect external speakers for monitoring and PA functions.
Covers turning the radio on/off, selecting channels, and adjusting volume.
How to transmit, use the PA system, and adjust microphone/volume.
How to adjust squelch level and use the Instant Channel 9 feature.
Recommended checks for VSWR, connections, cable, and screws.
Lists common issues like no power or poor reception with suggested solutions.
Guidelines for qualified technicians and specifying parts for service.
Details channels, frequency range, control, tolerance, and operating temperature.
Details transmitter power, modulation, and receiver sensitivity, selectivity, and IF frequencies.
States compliance with FCC Part 15 and Industry Canada RSS standards.
Outlines Industry Canada compliance and operational conditions.
Specifies warranty coverage, duration, invalidation conditions, and remedies.
Explains legal rights and limitations of the warranty, including exclusion of incidental damages.
Instructions on how to return the product for warranty service, including required documentation.
To Next Page
