Uniflame GBT1712W-U - User Manual

Questions and Answers

T
Troy McintyreAug 16, 2025
How to fix Uniflame GBT1712W-U igniter not working?
- P
  paulphamAug 16, 2025
  If the burner on your Uniflame Grill won't light using the igniter, several factors could be the cause. First, ensure the gas cylinder valve is open and the regulator is securely attached. If the gas cylinder is low or empty, refill or replace it. If you suspect LP gas issues, turn the gas cylinder valve to 'CLOSED,' wait 5 minutes, and then check for leaks. Also, inspect the wires and electrode for cooking residue and clean them with rubbing alcohol if needed. Wipe the electrode and burners dry if they are wet. If the electrode is cracked or the wire is loose, disconnected, or shorting, replacement parts may be needed. A bad igniter can also prevent ignition, in which case replacement parts are also needed.
T
Teresa WilliamsonAug 19, 2025
What to do if my Uniflame Grill has a flare-up?
- K
  Kathy ValentineSep 12, 2025
  If your Uniflame Grill experiences a flare-up, it's likely due to grease buildup or excess fat in the meat. Remove and clean all grill parts. Trim fat from meat before grilling to prevent future flare-ups. Also, excessive cooking temperature can cause flare-ups, so adjust to a lower cooking temperature.
A
Amy LittleAug 22, 2025
Why won't my Uniflame GBT1712W-U Grill burner light with a match?
- S
  Shannon TaylorAug 22, 2025
  If your Uniflame Grill burner won't light with a match, there could be several reasons. Check if the gas cylinder is empty and exchange, refill, or replace it if needed. If the gas cylinder is not empty, there may be an obstruction of gas flow. Clear the burner/venturi tube and check for a bent or kinked hose. Also, make sure the coupling nut and regulator are fully connected, tightening by hand only. Ensure the burner is properly engaged with the valve. Spider webs or insect nests in the venturi or clogged burner ports can also prevent lighting; clean these as necessary. If you suspect LP gas issues, turn the gas cylinder valve to “OFF”, wait 5 minutes, and then check for leaks.
B
Bruce CochranAug 25, 2025
What causes a sudden drop in gas flow in my Uniflame GBT1712W-U Grill?
- D
  Daniel TaylorAug 26, 2025
  A sudden drop in gas flow or reduced flame height in your Uniflame Grill can be due to a couple of reasons. The most common is simply running out of gas, so exchange, refill, or replace the gas cylinder. Alternatively, the overfilling prevention device may have been activated. To reset it: 1. Turn control knobs to • (OFF). 2. Wait 30 seconds and light grill. 3. If flames are still too low, reset the overfilling prevention device: a. Turn control knob(s) • (OFF). b. Turn Gas cylinder valve to “CLOSED”. c. Disconnect regulator. d. Turn control knobs to (HIGH). e. Wait 1 minute. f. Turn control knobs to • (OFF). g. Reconnect regulator and leak check connections, being careful not to fully open valve. h. Light grill.
H
Heather FloresAug 28, 2025
Why is the flame yellow on my Uniflame GBT1712W-U?
- S
  Sara BowenAug 28, 2025
  A yellow or orange flame on your Uniflame Grill can be caused by a few things. If it's a new burner, it may have residual manufacturing oils; burn the grill for 15 minutes on high with the lid closed to resolve this. Spider webs or insect nests in the venturi can also cause this issue; clean the venturi. Food residue or grease on the burners is another possibility, so clean the burner. Finally, poor alignment of the valve to the burner/venturi tube can be the culprit; ensure the burner/venturi tube is properly engaged with the valve.
J
Jessica WilliamsAug 31, 2025
Why does my Uniflame GBT1712W-U Grill flame keep going out?
- G
  Glenda Rush DVMAug 31, 2025
  The flame on your Uniflame Grill might be going out due to several reasons. High or gusting winds can extinguish the flame, so avoid using the grill in such conditions. Also, check if you're low on LP gas and exchange, refill, or replace the gas cylinder if needed. The overfilling prevention device may have been activated.
T
Timothy ChurchSep 3, 2025
How do I fix an irregular flame pattern on my Uniflame Grill?
- C
  Crystal HaleSep 3, 2025
  An irregular flame pattern on your Uniflame Grill, where the flame doesn't run the full length of the burner, is typically due to clogged or blocked burner ports. Clean the burner ports to resolve this issue.
R
Richard MorrisonSep 6, 2025
What causes flashback in my Uniflame GBT1712W-U Grill?
- D
  Derrick MillerSep 6, 2025
  Flashback, or fire in the burner tubes of your Uniflame Grill, is caused by blocked burners and/or burner/venturi tubes. Clean the burners and/or burner/venturi tubes to resolve this.
E
Eric EdwardsSep 8, 2025
What to do about a persistent grease fire in my Uniflame GBT1712W-U Grill?
- S
  Samantha ClarkeSep 8, 2025
  If you have a persistent grease fire in your Uniflame Grill, it's likely due to grease trapped by food buildup around the burner system. Here’s what to do: 1. Turn control knobs to • (OFF). 2. Turn gas cylinder valve to “OFF”. 3. Leave lid in closed position and let fire burn out. 4. After grill cools, remove and clean all parts.
U
uhoganSep 12, 2025
Why is the inside of my Uniflame GBT1712W-U Grill lid peeling?
- T
  Tara GarciaSep 12, 2025
  If the inside of your Uniflame Grill lid is peeling, it's likely due to baked-on grease buildup that has turned to carbon and is flaking off. Clean all grill parts.

Summary

Expanded View

Parts List

Assembly Instructions

Attach Brand Plate and Lid Handle

Attaches the brand plate and lid handle to the barbecue lid using specified hardware.

Attach Top Hinges

Connects the top hinges to the barbecue lid and bottom bowl assembly.

Attach Left & Right Leg Assembly

Assembles the left and right leg structures to the barbecue bottom bowl.

Attach Lock and Bottom Hinges

Secures the lock mechanism and bottom hinges to the barbecue frame.

Attach Valve Support, Regulator;Hose Assembly and Side Handles

Installs the valve support, regulator/hose assembly, and side handles.

Attach Bottom Bowl Heat Shield and Burner

Connects the bottom bowl heat shield and burner to the main assembly.

Attach Lid

Secures the main lid onto the assembled barbecue body.

Insert Warming Rack

Places the warming rack into its designated position within the grill.

Insert Heat Plate and Cooking Grid

Installs the heat plate and cooking grid onto the barbecue.

Locking and Unlocking Lid

Details on how to lock the lid for transport and unlock it for use.

Folding and Unfolding Legs

Instructions for folding the grill legs for storage and unfolding for use.

Installing LP Gas Cylinder

Gas Regulator

Connecting and Operating Conditions

Guidelines for connecting and operating the gas regulator safely.

Fitting the Hose

Steps to correctly attach the regulation rubber hose to the regulator.

Connect Gas Cylinder

Procedure for securely connecting the gas cylinder to the regulator.

Operating Regulator

Instructions on how to turn the gas regulator on and off.

Disconnecting Gas Cylinder

Steps for safely disconnecting the gas cylinder from the appliance.

Operation of Excess Flow Check Device

Explanation of the excess flow check device and its function.

Operating Instructions

Checking for Leaks

Procedure for performing leak tests on burner and tank connections.

First Use

Initial setup steps, including removing packaging and heat cleaning.

Lighting Instructions

Detailed steps for safely igniting the barbecue burners.

Turning Off

Procedure for safely turning off the barbecue after use.

Cooking

Guidance on cooking procedures, including preheating and flame adjustment.

Controlling Flare-ups

Methods and advice for managing and minimizing grill flare-ups.

Minimize Flare-ups

Specific tips to reduce excessive flare-ups during cooking.

Cleaning and Care

Before Each Use

Essential checks and cleaning required before operating the grill.

Cleaning Surfaces

Methods for cleaning the exterior surfaces of the barbecue.

Cleaning Main Burners

Instructions for disassembling and cleaning the main burner components.

Operating Instructions (continued)

Before Storing

Steps for preparing the grill for storage, including cleaning and disconnection.

Specifications

Refund Information

Customer Services Information

Contact Us

Troubleshooting

Burner will not light using igniter

Diagnoses and solutions for igniter issues.

Burner will not light with match

Troubleshooting steps for lighting the burner with a match.

No gas flow

Identifies causes and cures for lack of gas flow to the burner.

Sudden drop in gas flow or reduced flame height

Addresses issues with diminished gas flow or flame.

Irregular flame pattern, flame does not run the full length of burner

Solutions for uneven flame distribution across the burner.

Flame is yellow or orange

Diagnosing and fixing flames that are yellow or orange.

Flame goes out

Troubleshooting steps when the burner flame extinguishes.

Flare-up

Causes and management of grill flare-ups.

Persistent grease fire

Procedures for dealing with persistent grease fires.

Flashback (fire in burner tube(s))

Resolving issues where fire burns back into the burner tube.

Inside of lid is peeling (like paint peeling)

Explanation and resolution for peeling inside lid surfaces.

Uniflame GBT1712W-U Specifications

General

Brand	Uniflame
Model	GBT1712W-U
Category	Grill
Language	English

Related product manuals

Uniflame GBC976W

28 pages

Uniflame GBC920W1