6565
7.4 Stacking Load7.4 Stacking Load
··Slow down when approaching the load depositSlow down when approaching the load deposit
area.area.
··Stop the truck right in front of the area where yourStop the truck right in front of the area where your
load is to be deposited.load is to be deposited.
··Check the condition of the deposit area.Check the condition of the deposit area.
··Tilt the mast forward until forks becomeTilt the mast forward until forks become
horizontal. Raise forks until they are a little higher thanhorizontal. Raise forks until they are a little higher than
the deposit position.the deposit position.
··Move forward to place the load directly over theMove forward to place the load directly over the
desired area and stop the truck.desired area and stop the truck.
··Make sure your load is just over the desired area.Make sure your load is just over the desired area.
Slowly lower the load into position. Make sure the loadSlowly lower the load into position. Make sure the load
is securely stacked.is securely stacked.
··Disengaged forks from the load by usingDisengaged forks from the load by using
necessary liftnecessary lift--tilt operation and tilt operation and then back away.then back away.
··After After making making sure sure the the fork fork tips tips leave leave the the load,load,
lower the forks to the basic position (15 to 20 cm offlower the forks to the basic position (15 to 20 cm off
the ground).the ground).
··Tilt the mast backwards.Tilt the mast backwards.
!! WWaarrnniinngg
Never tilt the mast with loads upraisedNever tilt the mast with loads upraised
2m or more.2m or more.
Don‘t leave or dismount from the truckDon‘t leave or dismount from the truck
when the load is raised high.when the load is raised high.
7.5 Remove Load7.5 Remove Load
Slow down when approaching the area where theSlow down when approaching the area where the
load is to be retrieved.load is to be retrieved.
Stop the truck in front of the load so that theStop the truck in front of the load so that the
distance between the load and fork tips is about 30distance between the load and fork tips is about 30
cm.cm.
Check the condition of the load.Check the condition of the load.
Tilt the mast forward until forks become horizontal.Tilt the mast forward until forks become horizontal.
Elevate forks up to the position of the pallet or skid.Elevate forks up to the position of the pallet or skid.
Make sure forks are positioned properly for theMake sure forks are positioned properly for the
pallet. Move forward slowly to insert forks into thepallet. Move forward slowly to insert forks into the
pallet as far as possible and then stop the truck.pallet as far as possible and then stop the truck.
Raise the forks 5 to 10 cm off the stack.Raise the forks 5 to 10 cm off the stack.
!! CCaauuttiioonn
If the forks cannot be fully inserted, use theIf the forks cannot be fully inserted, use the
following procedure: move forward and insert thefollowing procedure: move forward and insert the
forks 3/4 of the forks 3/4 of the wayway. Raise the forks 5 . Raise the forks 5 to 10 cm andto 10 cm and
move backward 10 to 20 cm with the pallet or skidmove backward 10 to 20 cm with the pallet or skid
on the forks, then lower the pallet or skid on theon the forks, then lower the pallet or skid on the
stack. Move forward again to stack. Move forward again to insert the forks fully.insert the forks fully.
Check all around the truck to insure that the pathCheck all around the truck to insure that the path
of travel is unobstructed and back away slowly.of travel is unobstructed and back away slowly.
Lower forks to a height of 15 to 20 cm above theLower forks to a height of 15 to 20 cm above the
ground. Tilt the mast backward fully and move tground. Tilt the mast backward fully and move to theo the
desired area.desired area.
https://www.forkliftpdfmanuals.com/
To Next Page
Loading...
