Vermont Castings Signature VCS501 Series User Manual (English)

Questions and Answers:

B
bosborneJul 29, 2025
Why won't my Vermont Castings Signature VCS501 Grill burner light?
- M
  Michael ValdezJul 29, 2025
  Several factors can prevent your Vermont Castings Grill burner from lighting. First, check if the gas supply is turned on and if the propane tank is empty. You can confirm gas flow by smell or sound. Also, inspect for blockages in the gas system, especially in the venturi tubes (clean with a venturi brush) and the gas valve orifice (clean with a wire brush or toothpick, being careful not to enlarge it). Ensure the gas valve is aligned with the venturi tubes, and the propane hose and regulator are properly attached and tightened.
A
aaronjohnsonAug 2, 2025
Why won't my Vermont Castings Signature VCS501 stay lit?
- A
  Alison BrownAug 2, 2025
  Your Vermont Castings Grill might not stay lit due to wind or running out of fuel. Shield your grill from strong winds. To check the fuel, confirm the flow of gas by smell or by listening for a hissing sound. Weigh the propane cylinder to ensure it's not empty; a standard 20 lb cylinder weighs about 19 lbs when empty and 39 lbs when 80% full.
Z
zmartinAug 6, 2025
What to do if my Vermont Castings Grill has flare-ups?
- O
  omarchristianAug 7, 2025
  If your Vermont Castings Grill experiences flare-ups, take these steps: trim excess fat from meats before cooking to reduce grease. Make sure the sear plate and drip tray are clean and correctly installed to manage grease accumulation. Remove any excess grease from the burn chamber. If flare-ups persist, lower the heat setting.
A
Anthony McdonaldAug 11, 2025
How to fix my Vermont Castings Signature VCS501 Grill if it won't heat up on LP?
- T
  Timothy GomezAug 11, 2025
  If your Vermont Castings Grill isn't heating up on LP, it might be due to the flow control mechanism being engaged. This can happen if a control knob was left open during startup, the gas was turned on too quickly, or in cold/windy conditions. To fix it, close the cylinder valve, ensure all burner control knobs are OFF, slowly open the cylinder valve (1-2 turns) and wait 5 seconds, then turn on a single burner and try relighting it.
B
Brian BeanAug 15, 2025
What causes uneven burning or flashback fire in my Vermont Castings Grill?
- M
  Mandy WilsonAug 15, 2025
  Uneven burning or flashback fire in your Vermont Castings Grill can be caused by a blockage in the burner or gas system, or a corroded burner. Check the venturi tubes for blockages (clean with a venturi brush). Use a wire brush or toothpick to probe the gas valve orifice, being careful not to enlarge it. Clean the burner ports with a small nail or toothpick. If the burner is corroded, consider replacing it.
T
Tamara AdamsAug 19, 2025
How to troubleshoot a Vermont Castings Signature VCS501 igniter that doesn't spark?
- D
  Douglas LangAug 19, 2025
  If the igniter on your Vermont Castings Grill isn't sparking, try these steps: First, wipe the electrode with a clean cloth. Ensure the electrode is properly gapped (1/8” to 3/16”) from the burner and positioned to spark at the edge of a gas port; gently bend it into position if needed. Check for cracks in the ceramic insulator and replace the electrode if cracked. Make sure the lead wire is well-seated and not cracked; replace if necessary. Also, verify the battery in the igniter button is not dead or installed incorrectly (positive end down).
F
Felicia ShepardAug 25, 2025
Why does my Vermont Castings Grill have an excessive yellow flame?
- C
  Christine RamirezAug 25, 2025
  An excessive yellow flame on your Vermont Castings Grill usually indicates an improper air shutter opening. Your grill should burn with a predominantly blue flame. First, check the venturi tubes for obstructions and clean them. If the yellow flames persist, adjust the opening on the air shutter of the venturi tube located under the front console of the grill.

Vermont Castings Signature VCS501 Series Specifications

General

Number of Burners	3
BTU Output	36, 000 BTU
Material	Stainless Steel
Ignition System	Electronic
Grate Material	Porcelain-coated cast iron
Warranty	Limited Lifetime
Cooking Area	501 square inches