VEVOR 18151BX - User Manual

Questions and Answers

Q
qramirezAug 16, 2025
What to do if my VEVOR 18151BX is sluggish?
- A
  Alicia SantanaAug 16, 2025
  If your VEVOR Swimming Pool Vacuum is sluggish, try the following: * Check if the pump is ON or primed. * Inspect the cleaner head for blockages. * Clean and empty the pump basket, as well as the skimmer/weir basket. * Ensure the filtration system is thoroughly cleaned. * Clean sand/cartridge filters on your pool pump according to the manufacturer's specifications. * Inspect the regulator valve and flush away any debris buildup. * Check the mat for wear. * Make sure the curved tips of the mat are facing upwards. * Ensure that the skimmer/weir vacuum lid is fitted correctly and check for cracks.
D
Douglas PaceAug 19, 2025
Why is my VEVOR Swimming Pool Vacuum hose tangling?
- Q
  qbrightAug 19, 2025
  If the hose of your VEVOR Swimming Pool Vacuum is tangling, consider these solutions: * Ensure the wheel on top of the cleaner body rotates freely and is securely screwed on. * Check that the hose sections are straight; if not, lay the hose in a straight line in the sun to relax the memory. * If there are too many hose sections for your pool, try removing a section. * Inspect the regulator valve and flush away any debris buildup. * For pools where the skimmer is located at one end, improve cleaner performance by tying the hose off in the middle of the long side of your pool.
J
Joseph KnoxAug 21, 2025
How to fix if my VEVOR Swimming Pool Vacuum cleaner leaves patches?
- S
  Samantha LopezAug 21, 2025
  To address the issue of your VEVOR Swimming Pool Vacuum leaving patches, consider the following: * Ensure the wheel on top of the cleaner body is rotating freely and is screwed on securely. * Adjust the return jets downwards. * Verify proper hose length. * Ensure the cleaner sits flush with the pool floor. * Adjust the position of the hose weight if necessary. * Check that the hose sections are straight; if not, lay the hose in a straight line in the sun.
F
Frank HunterAug 25, 2025
What to do if VEVOR Swimming Pool Vacuum gets stuck on steps?
- C
  Christine Jackson MDAug 26, 2025
  If your VEVOR Swimming Pool Vacuum is getting stuck on steps, try these solutions: * Adjust the return jets toward the problem area to guide the cleaner away from the steps. * Verify proper hose length. * Ensure the cleaner sits flush with the pool floor. * Adjust the position of the hose weight if necessary. * Increase or decrease the flow to your cleaner via the regulator. * Check the mat for wear.
R
Rachel MyersAug 28, 2025
How to stop VEVOR 18151BX from traveling in a repetitive pattern?
- T
  Todd ZimmermanAug 28, 2025
  To correct a repetitive cleaning pattern with your VEVOR Swimming Pool Vacuum, try the following: * Adjust return jets downwards. * Verify proper hose length. * Ensure the cleaner sits flush with the pool floor. * Adjust the position of the hose weight if necessary. * Remove or add one hose section. * Inspect the regulator valve and flush away any debris buildup. * Check that the hose sections are straight; if not, lay hose in a straight line in the sun to relax the memory.
J
Joseph Smith MDAug 31, 2025
Why VEVOR 18151BX Swimming Pool Vacuum is not sitting flat on bottom?
- L
  lori48Aug 31, 2025
  If your VEVOR Swimming Pool Vacuum isn't sitting flat on the bottom of the pool, check the following: * Ensure there is a valve installed in the skimmer/weir. * Inspect the regulator valve and flush away any debris buildup. * Ensure the wheel on top of the cleaner body is rotating freely and is screwed on securely. * Adjust return jets downwards. * Verify proper hose length. * Ensure the cleaner sits flush with the pool floor. * Adjust the position of hose weight if necessary.
S
Sharon AlvaradoSep 3, 2025
How to prevent VEVOR 18151BX from climbing out of pool?
- C
  colleenwilsonSep 3, 2025
  To prevent your VEVOR Swimming Pool Vacuum from climbing out of the pool and drawing in air: * Ensure there is a valve installed in the skimmer/weir. * Inspect the regulator valve and flush away any debris buildup. * Verify proper hose length. * Ensure the cleaner sits flush with the pool floor. * Adjust the position of hose weight if necessary.
J
John GarciaSep 6, 2025
Why does my VEVOR 18151BX stick on walls and floors?
- T
  Tricia JonesSep 6, 2025
  If your VEVOR Swimming Pool Vacuum sticks to the walls and floors, try these steps: * Ensure there is a valve installed in the skimmer/weir. * Inspect the regulator valve and flush away any debris buildup. * Check the mat for wear. * Try increasing or decreasing the flow to your cleaner via the regulator.
Z
Zachary CummingsSep 9, 2025
Why are there air bubbles in the return jets with my VEVOR Swimming Pool Vacuum?
- C
  Claudia BowmanSep 9, 2025
  If you notice air bubbles in the return jets while using your VEVOR Swimming Pool Vacuum, check the following: * Ensure the cleaner hose is assembled tightly. * Ensure the cleaner head is not removed from the water while the pump is running. * Ensure the hoses are not damaged. * Ensure the regulator valve is underwater.
L
lindarussellSep 12, 2025
What to do if VEVOR 18151BX Swimming Pool Vacuum won't leave edge of pool?
- D
  David JonesSep 12, 2025
  If your VEVOR Swimming Pool Vacuum won't leave the edge or rim of the pool: * Utilize return jets to move the cleaner. * Adjust the hose weight. * Try decreasing the flow to your cleaner via the regulator.