Victron energy 12/30 User Manual

Victron energy 12/30

16 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

0

victron energy

GB NL F D I DK ΕΛ N P E S Specs

USER MANUAL

Phoenix Charger

12/30

12/50

24/16

24/25

Table of Contents

Questions and Answers:

B
Briana WatersJul 31, 2025
Why doesn’t my battery get fully charged with the Victron energy 12/30?
- L
  lisa27Aug 1, 2025
  If your battery isn't fully charging with the Victron Energy Battery Charger, several factors could be at play. It could stem from a bad battery connection, so check all connections. The absorption voltage might be incorrectly adjusted; in this case, you should consult your battery supplier and electrician to adjust the charging voltage. Also, the battery capacity might be too large for the charger, so ensure the charger matches the battery capacity. Finally, the output fuses could be defective, requiring you to return the product to your dealer.
P
Philip OliverAug 8, 2025
What to do if my Victron Energy Battery Charger is not functioning?
- T
  Taylor CraigAug 8, 2025
  If your Victron Energy Battery Charger isn't working, the issue might be with the mains voltage or a defective input fuse. First, measure the mains voltage to ensure it's within the specified range. If the voltage is correct, the input fuse may be defective, requiring you to return the product to your dealer.
Z
zacharyphamAug 16, 2025
What to do if my Victron energy 12/30 Battery Charger Failure LED illuminates?
- D
  donovanjonathanAug 16, 2025
  If the Failure LED illuminates on your Victron Energy Battery Charger, it could be due to defective output fuses or a high ambient temperature. If the output fuses are defect, return the product to your dealer. If the ambient temperature is too high, place the charger in a cool, well-ventilated environment.
M
Margaret SampsonAug 22, 2025
Why is the battery being overcharged by my Victron Energy Battery Charger?
- K
  Kelly MunozAug 22, 2025
  If your Victron Energy Battery Charger is overcharging the battery, it could be due to several reasons. The absorption voltage might be wrongly adjusted; consult your battery supplier and electrician to adjust the charging voltage. A single battery cell could be defective; replace the battery or the defective cell. The battery might be too small; consult your battery supplier and electrician to adjust the charging current. Also, the ambient temperature of the battery might be too high; consult your electrician and have them connect a temperature sensor.

Victron energy 12/30 Specifications

General

Input Voltage	230 VAC
Output Current	30 A
Maximum Output Current	30 A
Battery Type	Lead-acid (Gel, AGM, Flooded), Lithium-ion
Charging Stages	Bulk, Absorption, Float
Float Voltage	13.8 V (adjustable)
Storage Voltage	13.2 V (adjustable)
Output Voltage	12 V
Protection	Over-temperature, short-circuit, reverse polarity
Charge Voltage	14.4V (adjustable)
Operating Temperature Range	-20°C to +50 °C

Summary

SAFETY AND REGULATORY INFORMATION

General Safety

General safety precautions and regulatory compliance for equipment operation.

Installation Safety

Safety guidelines for product installation, wiring, and grounding.

Transport and Storage

Guidelines for safe handling during transport and storage of the charger.

PRODUCT DESCRIPTION

Technology and Design

Overview of the charger's high-frequency switching technology and internal design.

Charging Modes and Features

Details on Adaptive Charging, BatterySafe, and All Season modes.

Sensors and Outputs

Explanation of temperature sensor, voltage sense, and additional outputs.

CONTROLS AND TROUBLESHOOTING

Charger Controls and Modes

Operation, LED indicators, and special modes like Equalize and Force Absorption.

Troubleshooting Guide

Common problems, their causes, and solutions for the Phoenix Charger.

INSTALLATION PROCEDURE

Location and Tools

Recommended installation location, mounting, and required tools.

Connection Instructions

Step-by-step guide for electrical connections and wiring.

ADJUSTMENTS WITHOUT REMOTE PANEL

Adjusting Charging Parameters

How to adjust bulk current, absorption, and float voltages.

Settings Management

Restoring factory settings and final connection steps.

ADJUSTMENTS WITH REMOTE PANEL

Remote Panel Operation

Using the remote control panel for adjustments and settings.

Parameter and Battery Type Settings

Adjusting specific parameters and selecting battery types.

FACTORY SETTINGS OVERVIEW

Default Charging Configurations

Overview of default settings for intervals, times, and characteristics.

Battery Type Defaults

Default voltage and time settings for various battery types.

TECHNICAL SPECIFICATIONS

Electrical and Performance Specs

Detailed electrical parameters, current, and voltage specifications.

Environmental and Mechanical Specs

Specifications for operating environment, safety, and physical dimensions.

DETAILED FACTORY SETTINGS

Charging Intervals and Times

Default settings for repeated absorption interval and time.

Characteristic and Battery Type Settings

Default characteristic modes and specific battery type settings.

Related product manuals

Preview: Victron energy Phoenix 12/30

Victron energy Phoenix 12/30

Orion-Tr Smart 12/12-30

Preview: Phoenix Smart IP43 12/30

Phoenix Smart IP43 12/30

Phoenix Smart 12/30 (1+1)

Preview: Phoenix Multi Compact 12 800 35

Phoenix Multi Compact 12 800 35

Preview: Victron energy PALLAS-TG 12/50

Victron energy PALLAS-TG 12/50

Blue Smart IP22 12/15

Orion-Tr Smart 12/24-15

Preview: Orion-Tr Smart 12/12-18

Orion-Tr Smart 12/12-18

Orion-Tr Smart 24/12-20

Preview: Phoenix Multi 12/1600/70

Phoenix Multi 12/1600/70

Phoenix Inverter 12/1600