Victron energy Phoenix 48/800 User Manual (English)

Other manuals for Victron energy Phoenix 48/800

User Manual82 pages

Instruction Manual26 pages

Questions and Answers:

D
Daniel McbrideAug 8, 2025
How to fix a Victron energy Phoenix 48/800 Inverter that is not working (red LED OFF)?
- K
  Kelsey ParrishAug 8, 2025
  If your Victron Energy Inverter is not working and the red LED is off, check the following: * Power switch position: Ensure the power switch is in the ON (I) position. * Battery wire connections: Clean the battery terminals and inverter wire contacts to ensure good contact. Tighten the battery terminal screws. * Inverter fuse: If the fuse is blown, the inverter must be returned for service. * Battery condition: If the battery is in very poor condition, replace it.
J
Jonathan ColeAug 14, 2025
What to do if Victron energy Phoenix 48/800 Inverter shows ‘Overloaded or shorted output’ error?
- R
  richardmortonAug 15, 2025
  If the Victron Energy Inverter displays an ‘Overloaded or shorted output’ error, it could be due to several reasons: * The inverter might be overloaded. Ensure the total power rating of the connected equipment is less than the inverter's nominal power rating. * The connected equipment may have a bad power factor. Reduce the power consumption of the load. Note that some devices, like computers, can reduce the inverter's maximum output power by approximately 20%. * A short circuit might exist in the connected equipment. Verify that the equipment is functioning correctly and inspect the AC power cord for any damage that could cause a short circuit. Exercise caution during inspection.
M
Mrs. Maureen ClarkAug 20, 2025
Why does my Victron energy Phoenix 48/800 Inverter keep showing ‘Battery voltage too low or too high’ error?
- B
  Barbara EvansAug 20, 2025
  The ‘Battery voltage too low or too high’ error on your Victron Energy Inverter can be caused by: * Poor battery condition: Replace the battery or charge it. * Poor connection or inadequate wiring: This can lead to excessive voltage drop between the battery and inverter. When extending the inverter's battery wires, use a wire gauge that is at least 1.5 times larger than the original wires. It is not recommended to extend the battery wires beyond 3 meters. * General electrical system failure: If there is no direct battery connection, check your electrical system or consult an electrical engineer.
E
Erin SandersAug 26, 2025
What to do if Victron energy Phoenix 48/800 displays ‘Inverter temperature too high. Cooling down’ error?
- S
  Stephen McconnellAug 27, 2025
  If your Victron Energy Inverter shows an ‘Inverter temperature too high. Cooling down’ error, the issue could be: * Obstructed airflow: Ensure there is at least 10 centimeters of clearance around the inverter. Remove any items placed on or over it, and keep it away from direct sunlight or heat-producing equipment. * High ambient temperature: Move the inverter to a cooler location or provide additional cooling with an external fan.
K
kimberly94Aug 31, 2025
Why does my Victron Energy Inverter jump between continuous mode and economy mode?
- W
  whitelorraineAug 31, 2025
  The Victron Energy Inverter may switch between continuous mode and economy mode frequently if the connected load is not compensated, or if the ratio between inrush current and continuous current is too large. To resolve this, connect an additional load to the output.

Victron energy Phoenix 48/800 Specifications

General

Model	Phoenix Inverter 48/800
Input Voltage	48 V
Output Power	800 VA
Output Voltage	230 VAC
Output Frequency	50 Hz or 60 Hz
Peak Power	1600 W
Transfer Time	20 ms
DC Voltage Range	38-66V DC
Protection	Output short circuit, Overload, Over-temperature