Vincent
33993388
Vincent
OPERATING THE APPLIANCE
ADVANCED PLAYBACK FUNCTIONS
Operation Button(s) Description
Delete the selected
playing sequence
CANCEL
(24)
This button deletes a program set up with the “PGM” function (25). If no pro-
gram has been set up, then this button has no function. If the button is pressed
during a pause, any selected program will be deleted and you can continue
to play the current track and the remaining CD tracks with “PLAY/PAUSE"
(6)(19). Just as with the program set-up, this action may only be performed
with the remote control.
Switch between normal
and random playback
RANDOM
(26)
The function activated with this remote control button ensures that all the CD
tracks are played in random order. This function cannot be used for playing a
program set up with “PGM” (25). If this button is pressed during play or
pause, the current track is stopped and the playing of all the CD tracks in ran-
dom order begins. In the display, this play mode will be indicated by the text
“RAN”. Pressing the “RANDOM” button again switches off random playing
and playing will continue from the current position.
Switch between playing
the content of the CD
once, repeating an indivi-
dual track and repeating
all the tracks on the CD
REPEAT (18)
If this button is pressed once while the CD is playing, the current track will
be played over and over again when it has finished. In the display (2) this
operation mode is indicated by the text “REPEAT 1”. If this button is pres-
sed twice while the CD was playing, then the entire CD or the entire pro-
gram will be played over and over again when it has finished. In the dis-
play (2) this operation mode is indicated by the text “REPEAT ALL”. A third
press of the key switches this function off. The desired repeat mode can
also be switched on even when play is stopped or for a selected pro-
gram. The “REPEAT” button is only on the remote control.
Repeat a custom
section of the track
as an endless loop
A-B (16)
While the CD is playing, the first press of this key marks the start of the
section (A) and the second press marks the end of this section (B). As soon
as both points are selected, the player continues to play the marked
extract over and over again until the “A–B” key is pressed again or
“STOP” (7)(21) is pressed. In the display (2) this play mode is indicated
with the symbol “A< >B”. After the A-B playback has been stopped with
the “STOP” key (7)(21), the marked points will be deleted. This play opti-
on too can only be controlled via the remote control.
Play a short introduction
of every track
INTRO (17)
You can press this remote control key if the beginnig of every track is only
to be played for a brief time. In this mode the first ten seconds of the track
will be played then it will skip to the next track in the sequence. This functi-
on is also known by the term “Intro Scan“. Even if a program has been set
up for the play sequence (25), all the CD tracks will each be played once
for a brief time after the “INTRO” key has been pressed. Pressing this key
again ends the Intro Mode and continues playing the remaining section
from the current position onwards. The text “INTRO” will be shown on the
display (2) while the “Intro Sscan” is active. If this key is pressed during
play or pause, the Intro Mode always starts with the first CD track.
ADVANCED PLAYBACK FUNCTIONS
Operation Button(s) Description
Program the
playback order
PGM (25)
With this function it is possible to set up a desired playing sequence of the
CD tracks. This also allows you to play a smaller selection of your own choice
from all the CD tracks. This programming can only be done with the remote
control. The “program” is set up by the following procedure:
• Press the PGM button
• Enter the numbers of all the desired tracks one after the other on the
number pad (15) of the remote control. For track 10 use the "10” but-
ton. For all other two-figure track numbers first press the “+10” button
as many times as necessary until the number of 10’s is correct, then
press the button for the last figure (for track 23 press the “+10” but-
ton twice and the “3" button once).
• To confirm the program press “PGM” or “PLAY/PAUSE” (6)(19). The
program will be run immediately. If the “REPEAT” function (18) is not
then operated, the program will run once and then be deleted.
The “REPEAT” play function (18) can also be applied to the programmed
track selection. In this case, even if "STOP” (7)(21) is pressed, the program
remains in the memory and it will run again with the next play. You can see
on the display from the text “PGM” that a program is active. It is only if you
press “CANCEL” (24), eject the CD or switch off the CD player that your own
playing sequence is deleted.
Indication of the
remaining playing time
REMAIN (14)
After pressing this remote control key while the CD is playing, the remaining
time of the current track will be shown (indicated by the text “REMAIN" in the
display (2)). Pressing the key again switches the display to the remaining play-
ing time of the entire CD or the entire program, with the display then showing
“REMAIN ALL”. Pressing the key a third time switches back to the normal play-
ing time display.
OPERATING THE APPLIANCE
PLAYING HDCD’S
Any HDCD inserted is recognised automatically.
The HDCD LED will only light up if an HDCD is
inserted, if it has been started and if the output
level of the analogue outputs has been set to its
maximum value of “26” (“VOL” keys (29)(30)).
The HDCD signal will only be decoded if this dis-
play lights up!
To Next Page
Loading...
