8
BEFORE THE FIRST USE
After unit transportation or storage at low temperature
keep it for at least three hours at room temperature
before switching on.
There may be water residue inside the kettle, this is normal, as
the unit has undergone factory quality control.
– Unpack the kettle and remove any stickers that can prevent
unit operation.
– Check the unit for damages; do not use it in case of dam-
ages.
– Make sure that the unit operating voltage corresponds to
the voltage of your mains.
– Place the kettle on the base (8).
Note: There is a cord storage (9) on the reverse side of the
base (8). You can adjust the optimal length of the power cord
by arranging it appropriately in the cord storage.
– Insert the power plug into the mains socket. You will hear
a sound signal, the touch buttons (7) will be highlighted,
the display (6) will show the temperature inside the kettle.
Note: The kettle control buttons are touch-sensitive. To select
the desired operating mode, simply touch the button. Each
press of a button is accompanied by a short sound signal.
– To fill the kettle with water, remove it from the base (8) - the
touch buttons (7) will no longer be highlighted and the dis-
play (6) will turn off. Then, open the kettle lid (3) by pressing
the lid-opening button (4).
– Fill the kettle with water up to the maximum level mark «MAX».
– Close the lid (3), place the kettle on the base (8). Make
sure that the kettle lid (3) is closed tightly. You will hear a
sound signal again, the touch buttons (7) will become high-
lighted, the display (6) will show the temperature of the
water in the kettle.
Note: If no button is pressed within 1 minute, the kettle will go
into standby mode: the display (6) and all the touch buttons
will no longer be highlighted, except for the on/off button .
The highlight of the on/off button , will slowly dim. Press the
on/off button to exit the standby mode.
– To boil water, press the Boil button. The process of boil-
ing will start, the display (6) will show the current tempera-
ture of the water, and the Boil button, Warm temperature
maintenance button and on/off buttons will become
highlighted.
Note: Press the on/off button again to manually stop the
boiling.
– Once the water has boiled, you will hear a double sound sig-
nal, the display (6) will show the water temperature 100 °С,
the boiling will stop. After a time (~25 sec.) the display will
turn off and the kettle will go into standby mode.
– Drain the water and repeat the water boiling procedure
2-3 times.
ATTENTION! To avoid getting burned by hot steam, do not
lean over the kettle spout (2) while it is operating.
USING THE KETTLE AND ADDITIONAL FUNCTIONS
– Insert the power plug into the mains socket.
– To fill the kettle with water, remove it from the base (8), open
the lid (3) by pressing the lid opening button (4).
– Fill the kettle with water no higher than the maximum level
mark «MAX».
– Close the lid (3) and put the filled kettle on the base (8).
Make sure that the kettle lid (3) is closed tightly. You will
hear a sound signal, the touch buttons (7) will be high-
lighted and the display (6) will show the temperature of the
water in the kettle.
Note: If no button is pressed within 1 minute, the kettle will go
into standby mode: the display (6) and all the touch buttons will
no longer be highlighted, except for the on/off button . The
highlight of the on/off button , will slowly dim. Press the on/
off button to exit the standby mode.
Water boiling mode
To boil water, press the Boil button. The process of boiling will
start, the display (6) will show the temperature of the water, the
Boil button, Warm temperature maintenance button, and on/
off buttons will become highlighted.
– Once the water has boiled, you will hear a double sound sig-
nal, the display (6) will show the water temperature 100 °С,
the boiling will stop. After a time (~25 sec.) the display will
turn off and the kettle will go into standby mode.
– You can switch off the kettle during the boiling process by
pressing the on/off buttons - the touch buttons (7) will
be highlighted and the display (6) will show the current tem-
perature of water inside the kettle.
Fixed water heating mode
– This kettle allows you to heat water to 70, 80, and 90 °C.
To select a fixed heating temperature, turn on the kettle
by pressing the button - you will hear a sound signal,
and the touch buttons (7) will be highlighted. To heat the
water to 70 °C, press the 70 button. To heat the water to
80 °C, press the 80 button, and to heat the water to 90 °C,
press the 90 button. The heating process will start, and
the display (6) will show the current water temperature.
The Warm, on/off button , and 70, 80, or 90 °C but-
tons will be highlighted, depending on the selected heat-
ing temperature.
– Once the water has heated up to the set temperature, you
will hear a double sound signal, the display (6) will show the
set water temperature, and the heating process will stop.
After a time (~25 sec.) the display will turn off and the kettle
will go into standby mode.
– You can switch off the kettle during the heating process by
pressing the on/off buttons - the touch buttons (7) will
be highlighted and the display (6) will show the current tem-
perature of water inside the kettle.
User-defined heating mode
– This kettle allows for heating water to a temperature
between 40 and 100 °С, with a 5 °С step.
– Switch on the kettle and select the desired temperature by
pressing the button - you will hear a sound signal and
the touch buttons (7) will be highlighted.
– To enter the user-defined heating mode, press the «+»
or «-» button - the display (6) will show the low heating
limit – 40 °С.
– Use the «+» or «-» buttons to set the desired temperature
between 40 and 100 °С with a 5 °С step. After a few sec-
onds the heating process will begin and the display (6) will
show the current water temperature. The «+»/«-» buttons,
Warm temperature maintenance button, and on/off but-
tons will be highlighted .
– Once the water has heated up to the set temperature, you
will hear a double sound signal, the display (6) will show the
set water temperature, and the heating process will stop.
After a time (~25 sec.) the display will turn off and the kettle
will go into standby mode.
– You can switch off the kettle during the heating process by
pressing the on/off buttons - the touch buttons (7) will
To Next Page
Loading...