Vivitar DF200 User Manual

ENGLISH
Parts Description
1.
Zoom Indicator
2.
Zoom Head
3.
Fresnel Lens
4.
Sensor
5.
Decorative Front Panel
6.
Locking Ring
7.
Mounting Base
8.
Battery Cover
9.
Ready indicator (orange LED)
10.
Flash On/Off and Mode Switch
11.
Hold Button
12.
Tilting Angle Scale
13.
Swivel Angle Scale
14.
Distance Table
15.
Detection Indicator (green LED)
16.
Power Ratio Switch
17.
Power-On indicator (red LED)
18.
Bracket (not shown in diagram)
CAUTION  Read this section before use
§ The DF200 flash unit is designed to be used with any
digital camera with a built-in flash. The DF200 can be
used as a supplemental slave flash.
§ The DF200 flash unit contains high voltage circuitry. To
avoid electrical shock or burn, do not attempt to dismantle
any part of the flash. If the external shell of the flash unit
is broken or cracked, do not touch the internal
mechanisms or circuitry even when the batteries are
removed.
§ When replacing the batteries, replace all of the battery
cells. With weaker cells, the flash unit will take longer to
recharge for the next shot.
§ The DF200 flash unit is neither weatherproof nor
waterproof. When using the DF200 in the rain or near
water, avoid any contact with water. The warranty does
not cover water damage. It is often impractical to repair
electrical components damaged by water.
Batteries
The DF200 flash unit uses four AA batteries. You may use
alkaline, NiCD, or NiMH rechargeable batteries. Manganese
batteries are not recommended, because of shorter life and
longer flash recharging time.
Replace the batteries if the Orange Ready LED Indicator
takes more than 30 seconds to illuminate after each flash
shot.
1
8
9
10
11
12
13
15
14
16
17
7
1
2
3
4
5
6

Vivitar DF200 Specifications

General

Power Source	4 x AA batteries
Swivel Head	No
Guide Number (ISO 100)	20m / 66ft
Flash Modes	Auto, Manual
Tilt Head	Yes
Compatibility	Universal

Summary

ENGLISH

Parts Description

Identifies and lists all components of the DF200 flash unit for user reference.

Safety Cautions

Provides essential warnings regarding high voltage, potential damage, battery handling, and water exposure.

Battery Information

Details the type of batteries used (AA) and recommended types for optimal performance.

Battery Operations

Battery Precautions

Advises on proper battery handling to prevent explosion, leakage, overheating, and damage.

Battery Installation

Step-by-step guide for inserting AA batteries into the flash unit and confirming power.

Auto Standby System

Explains the flash's automatic power-saving standby mode and when to manually switch off.

Low-Battery Power Indication

Describes how the ready indicator signals battery depletion and when to replace batteries.

Attaching and Using the Flash

Attaching and Removing the Flash

Instructions on securely mounting the flash unit onto a camera bracket and removing it.

Distance Table for Zoom Head

Provides guidance on selecting the flash zoom position based on camera focal length and distance.

Flash Photography Setup

Guides users on setting camera white balance, flash mode, and profiling the DF200 to the camera.

Advanced Flash Features

Hold (Manual Standby) Feature

Explains how to temporarily suspend the DF200's operation to prevent unintended triggering.

Power Output Adjustment

Details how to manually adjust flash output power using the power ratio switch for exposure control.

Bounce Flash Technique

Describes how to tilt the flash head to bounce light off surfaces for softer lighting and reduced shadows.

Usage Precautions and Specifications

Precautions During Use

Advises on handling the flash unit carefully, avoiding extreme conditions, and proper cleaning methods.

Important Notes

Provides general advice on storage, product updates, and potential variations from manual descriptions.

Technical Specifications

Lists key technical details including guide number, zoom range, power settings, and dimensions.