How to fix no image on Vivitek DX881ST screen?
If no image appears on the screen of your Vivitek Projector, verify the settings on your notebook or desktop PC. You can also turn off all equipment and power up again in the correct order.
What to do if there is no light from Vivitek DX881ST Projector?
If there is no light from the Vivitek projector, check that the power cable is securely connected and ensure the power source is working by testing with another electrical device. Restart the projector and check that the Power LED is on. If you have recently replaced the lamp, try resetting the lamp connections. As a last resort, replace the lamp module.
How to fix blurred image on Vivitek Projector?
If the Vivitek Projector image is blurred, try the following: 1. Adjust the Focus on the projector. 2. Press the Auto button on the remote control. 3. Ensure the projector-to-screen distance is within the specified range. 4. Check that the projector lens is clean.
What to do if Vivitek Projector remote control not working?
If your Vivitek Projector does not respond to the remote control, ensure the remote control is pointed towards the remote sensor on the projector and that there are no obstructions between them. Also, turn off any fluorescent lights or Infrared-enabled devices nearby. Check the battery polarity and replace the battery if needed.
How to correct trapezoid effect on Vivitek Projector image?
If the image from the Vivitek Projector is wider at the top or bottom (trapezoid effect), position the projector so it is as perpendicular to the screen as possible. Alternatively, use the Keystone button on the remote control to correct the problem.
How to fix reversed image on Vivitek DX881ST Projector?
If the Vivitek Projector image is reversed, check the Projection setting on the Settings 1 menu of the OSD.
How to troubleshoot distorted sound on Vivitek DX881ST Projector?
If the sound from the Vivitek Projector is distorted, check the audio cable connection and test the source audio output with other speakers.
How to resolve streaked image on Vivitek Projector?
If the Vivitek Projector image is streaked, set the Frequency and Tracking settings on the Image->Computer menu of the OSD to the default settings. To ensure the problem is not caused by a connected PC’s video card, connect to another computer.
What to do if Vivitek DX881ST Projector image is flat with no contrast?
If the Vivitek Projector image is flat with no contrast, adjust the Contrast setting on the Image menu of the OSD.
How to adjust color on Vivitek DX881ST?
If the color of the projected image from your Vivitek Projector does not match the source image, adjust the Color Temperature and Gamma settings on the Image->Advanced menu of the OSD.
Provides essential safety guidelines for projector use, including handling, placement, and eye protection.
Details recommended tilt angles and minimum clearance around vents for proper installation.
Covers power supply, grounding, voltage stability, and avoiding specific environmental factors.
Specifies safe practices for using the power cord and handling batteries.
Details procedures and warnings for replacing the projection lamp and cleaning the unit.
Details the buttons and LED indicators located on the top of the projector.
Illustrates and labels all input and output ports on the rear of the projector.
Identifies and labels all buttons and components of the remote control.
Guides users through the procedures for powering the projector on and off.
Explains how to set up a password to prevent unauthorized use of the projector.
Covers adjusting image focus, correcting keystone distortion, and controlling audio volume.
Explains remote control and monitoring via wired LAN and compatibility with control systems.
Describes using RS232 commands over a LAN/RJ45 interface via Telnet for remote control.
Provides instructions and warnings for replacing the projector lamp and resetting its hour counter.
Offers general tips for resolving common projector issues, starting with basic checks.
Lists LED error codes and their corresponding projector status or faults.
General| Resolution | XGA (1024 x 768) |
|---|---|
| Speaker | 10W |
| Projection Technology | DLP |
| Native Resolution | XGA (1024 x 768) |
| I/O Ports | HDMI |
| Output Connectors | VGA Out |
| Keystone Correction | Vertical ±40° |
| Operating Temperature | 40 °C |
| Storage Temperature | 60°C |
To Next Page
