What to do if the lamp goes off on my Vivitek Projector?
If the lamp of your Vivitek Projector goes off, it might be due to power surges. Try re-plugging the power cord and, when the Ready LED is on, press the power button. If the problem continues, replace the lamp module. If this doesn't solve the problem, put the old lamp back in the projector and have it serviced.
What to do if there is no light from my Vivitek D825MS Projector?
If your Vivitek Projector has no light, first, ensure the power cable is securely connected and that the power source is functioning correctly by testing it with another electrical device. Then, restart the projector and check if the Power LED is green. If you've recently replaced the lamp, try resetting the lamp connections. If the issue persists, replace the lamp module. As a final step, you can put the old lamp back in and have the projector serviced.
How to fix no image on Vivitek D825MS Projector screen?
If no image appears on the screen when using your Vivitek Projector, verify the settings on your notebook or desktop PC. If that doesn't resolve the issue, turn off all equipment and power it up again in the correct order.
How to resolve a blurred image on a Vivitek D825MS?
If the image from your Vivitek Projector is blurred, start by adjusting the focus on the projector. If that doesn't sharpen the image, press the Auto button on the remote control or projector. Also, ensure the projector-to-screen distance is within the specified 10-meter (33-feet) range and check that the projector lens is clean.
What to do if my Vivitek D825MS remote control is not working?
If your Vivitek Projector isn't responding to the remote control, first, make sure you're directing the remote control towards the remote sensor on the projector and that there are no obstructions between them. Try turning off any fluorescent lights in the room and check the battery polarity. If it still doesn't work, replace the batteries. Also, turn off other Infrared-enabled devices nearby. If none of these steps work, have the remote control serviced.
How to correct trapezoid effect on Vivitek D825MS Projector image?
If the image from your Vivitek Projector appears wider at the top or bottom (trapezoid effect), position the projector so it is as perpendicular to the screen as possible. If the issue persists, use the Keystone button on the remote control or projector to correct the problem.
Why is there no sound coming from my Vivitek D825MS?
If there is no sound from your Vivitek Projector, first adjust the volume on the remote control and the audio source. Then, check the audio cable connection. Test the source audio output with other speakers to isolate the problem. If the issue persists, have the projector serviced.
What causes distorted sound in a Vivitek Projector?
If the sound from your Vivitek Projector is distorted, begin by checking the audio cable connection. Next, test the audio output of your source with other speakers to determine if the problem lies with the projector or the source. If the distortion persists, have the projector serviced.
How to fix a streaked image on a Vivitek D825MS?
If the image from your Vivitek Projector is streaked, set the Frequency and Tracking settings on the Computer menu of the OSD to the default settings. To ensure the problem isn't due to a connected PC’s video card, connect to another computer.
How do I correct a reversed image on my Vivitek Projector?
If the image from your Vivitek Projector is reversed, check the Projection setting on the Installation I menu of the OSD.
Provides essential safety instructions for operating the projector to ensure safe usage.
Lists items included with the projector for initial setup.
Step-by-step guide for installing batteries in the remote control.
Explains how to navigate and use the projector's OSD menu system.
Restores all projector settings to their factory default values.
Detailed steps and warnings for safely replacing the projector's lamp module.
Guidance on safely cleaning the projector lens with cleaner and soft cloth.
General| Projection distance | 0.9 - 9.1 m |
|---|---|
| Vertical scan range | 43 - 87 Hz |
| Horizontal scan range | 15.30 - 91.4 kHz |
| Projection technology | DLP |
| Screen size compatibility | 24.6 - 300 \ |
| Projector native resolution | SVGA (800x600) |
| Keystone correction, vertical | -30 - 30 ° |
| Offset | 114 % |
| Zoom capability | Yes |
| Focal length range | 0 mm |
| Mounting | Table Top/Ceiling |
| Audio input | Mini-Jack |
| Aspect ratio | 4:3, 16:9 |
| Compatibility | WUXGA, WXGA+, WXGA, UXGA, SXGA+, SXGA, XGA, SVGA, VGA VESA PC/Mac |
| Dimensions (WxDxH) | 280 x 205 x 96 mm |
| Connectivity technology | Wired |
| Lamp power | 180 W |
| Light source type | Lamp |
| Service life of light source | 3000 h |
| Service life of light source (economic mode) | 4000 h |
| RMS rated power | 1 W |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| S-Video inputs quantity | 1 |
| Display diagonal | 0.55 \ |
| Display number of colors | 1.073 billion colors |
| Placement | Ceiling |
| Cable lock slot type | Kensington |
| Power consumption (typical) | 230 W |
| Power consumption (economy mode) | 210 W |
| Operating temperature (T-T) | 5 - 40 °C |
Weight and Dimensions| Weight | 2600 g |
|---|
To Next Page
