Vulcan-Hart SX Series - User Manual

Vulcan-Hart SX Series

20 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

!

!

INSTALLATIO N(& (OPERATION(M A N U AL(

Gas(Restaurant( Ranges(

INSTRUCTION MANUAL

Vulcan SX Series Gas Ranges

SX36, SX60, SX60F

F-47673 (09/2016)

Table of Contents

Questions and Answers

J
Julie ValenzuelaAug 12, 2025
How to fix Vulcan-Hart SX Ranges pilot flame that won't ignite?
- M
  Monique LoveAug 12, 2025
  If your Vulcan-Hart Ranges pilot flame can't be ignited, it might be due to several reasons: * The gas pressure might be too low. In this case, adjust the relieve valve to increase the pressure. * The nozzle might be clogged, requiring you to unclog it. * A loose thermocouple connection could be the culprit; tighten it. * The thermocouple itself might be defective, necessitating a replacement. * The gas control valve may be malfunctioning, which means it should be replaced.
I
iflemingAug 18, 2025
Why my Vulcan-Hart SX has a yellow flame and black smoke?
- A
  Alisha SaundersAug 19, 2025
  If your Vulcan-Hart Ranges has a yellow flame and black smoke, it could be due to several reasons: * The orifice size might be incorrect for the gas supply, so install the proper orifice. * The damper might be closed too far; adjust the damper. * You might be running out of gas/propane; replace the tank or increase the gas supply. * High elevation could be a factor; install proper orifices for the elevation. * There might be a bad air/gas mixture; increase the airflow/gas to the unit.
J
Jonathan WestAug 27, 2025
What to do if Vulcan-Hart SX pilot flame is on but the main burner won’t ignite?
- K
  Kyle JenkinsAug 27, 2025
  If the pilot flame is on but the main burner can’t be ignited on your Vulcan-Hart Ranges, consider the following: * The gas pressure might be too low. Adjust the relieve valve to increase the pressure. * The main burner nozzle might be clogged. Unclog the nozzle. * The gas control valve might be defective. Replace the gas control valve.
L
Lawrence TorresSep 3, 2025
Why does my Vulcan-Hart SX make a light-back sound when turned off?
- S
  Stacey MedinaSep 3, 2025
  If your Vulcan-Hart Ranges makes a light-back sound when the gas supply is turned off, it could be due to: * An incorrect orifice size for the gas supply. Install the proper orifice. * The damper being too open. Adjust the damper. * Gas pressure being too low. Increase the gas pressure.

Vulcan-Hart SX Series Specifications

General

Model	SX Series
Burner Material	Cast Iron
Construction	Stainless Steel
Dimensions (WxDxH)	Varies by model
Weight	Varies by model
BTU	Varies by burner
Fuel Type	Natural Gas or Propane
Burner Type	Open Burner
Number of Burners	4, 6
Oven Type	Standard

Related product manuals

Vulcan-Hart SX60F

Preview: Vulcan-Hart 36-S-36G-N

Vulcan-Hart 36-S-36G-N

Preview: Vulcan-Hart GH6

Vulcan-Hart GH6

Preview: Vulcan-Hart MG12

Vulcan-Hart MG12

Preview: Vulcan-Hart GH30

Vulcan-Hart GH30

Vulcan-Hart GH60

Preview: Vulcan-Hart E24L

Vulcan-Hart E24L

Preview: Vulcan-Hart VG260

Vulcan-Hart VG260

Preview: Vulcan-Hart EG160

Vulcan-Hart EG160

Preview: Vulcan-Hart V60-1

Vulcan-Hart V60-1

Preview: Vulcan-Hart 260L SERIES

Vulcan-Hart 260L SERIES

Preview: Vulcan-Hart Value Series V36-1

Vulcan-Hart Value Series V36-1