WAGNER FLEXIO 3550 18V - Maintenance; Replacing the Filter; Troubleshooting

TROUBLESHOOTING
12
MAINTENANCE • ENTRETIEN • MANTENIMIENTO
REPLACING THE FILTER
Attention
Before every use, you should inspect the air
lter in the turbine to see if it is excessively
dirty. If it is dirty, follow these steps to
replace it.
Never operate your unit without the air
lters. Dirt could be sucked in and interfere
with the function of the unit.
1. Press the tab at the rear of the turbine. Slide the rear
housing o of the back of the turbine.
2. Remove the dirty lter from the turbine and replace
with a new one. The smooth side of the air lter must
be placed toward the turbine.
Secure the cover back onto the turbine.
REMPLACEMENT DU FILTRE
Attention
Vous devriez inspecter les ltre à air qui est
situé dans la turbine pour vérier s’il est
excessivement encrassé. S’il est encrassé,
veuillez suivre les étapes ci-dessous pour le
remplacer.
Ne jamais faire fonctionner votre appareil
sans le ltre à air. Des impuretés pourraient
être aspirées et causer des inter-férences
dans le fonctionnement de l’appareil.
1. Appuyez sur l’onglet à l’arrière de la turbine. Retirez le
boîtier arrière en le glissant de la turbine.
2. Enlevez le ltre souillés de la turbine et remplacez-les
par de nouveaux. Le côté lisse du ltre à air doit être
placé vers la turbine.
Remettez le couvercle sur la turbine.
REEMPLAZO DEL FILTRO
Atención
Es conveniente que inspeccione el ltro
de aire de la turbina para controlar si está
excesivamente sucio. Si se encuentra
sucio, siga los pasos a continuación para
reemplazarlo.
Nunca haga funcionar la unidad sin le ltro
de aire. La suciedad puede ingresar en la
unidad e interferir con su funcionamiento.
1. Presione la lengüeta en la parte posterior de la
turbina. Deslice la carcasa posterior y sáquela de la
parte posterior de la turbina.
2. Retire le ltro sucios de la turbina y reemplácelos por
nuevo. Se debe colocar el lado suave del ltro de aire
hacia la turbina.
Fije le tapa de vuelta en la turbina.
PROBLEM CAUSE SOLUTION
Problem A: Little or no material ow 1. Nozzle clogged.
2. Suction tube clogged.
3. Material ow setting too low.
4. Suction tube loose.
5. No pressure build up in container.
6. Air lter clogged.
7. Spray material too thick.
8. Nozzle seal missing or worn.
1. Clean.
2. Clean.
3. Increase material ow setting.
4. Remove and replace as tightly as possible.
5. Tighten container. Check the air vent hole on the pick
up tube - clean if clogged.
6. Change
7. Thin.
8. Replace nozzle.
Problem B: Material leaking 1. Nozzle loose.
2. Nozzle worn.
3. Nozzle seal missing or worn.
4. Material build-up on air cap and nozzle
1. Tighten.
2. Replace.
3. Replace nozzle.
4. Clean.
Problem C: Spray pattern too thick, runs and sags 1. Material ow setting too high.
2. Air power setting too low.
3. Applying too much material.
4. Nozzle clogged.
5. Air lter clogged.
6. Too little pressure build-up in container.
7. Spray material too thick.
1. Decrease material ow setting.
2. Increase air power setting.
3. Adjust material ow or increase movement of spray
gun.
4. Clean.
5. Change.
6. Tighten container. Check the air vent hole on the pick
up tube - clean if clogged.
7. Thin.
Problem D: Spray jet pulsates 1. Material in container running out.
2. Air lter clogged.
1. Rell.
2. Change.
Problem E: Too much overspray 1. Gun too far from spray object. 1. Reduce distance (6”-8” is ideal).
Problem F: Pattern is very light and splotchy 1. Moving the spray gun too fast.
2. Material ow setting too low.
3. Air power setting too high.
1. Adjust material ow or decrease movement of spray
gun.
2. Increase material ow setting.
3. Decrease air power setting.