What to do if my WAGNER Sprint 60 L XE Paint Sprayer has no powder feed?
If the WAGNER Paint Sprayer isn't feeding powder, first check if the tank or powder tank is empty and refill it. Then, ensure the spray gun, powder feed hose, and powder suction system aren't clogged by blowing through them. Also, check if the feed air hose or powder feed hose is bent or kinked; straighten or replace them if necessary.
How to fix sputtering powder feed on a WAGNER Sprint 60 L XE?
If you're experiencing sputtering powder feed with your WAGNER Paint Sprayer, it could be due to a low flow rate in the powder feed hose. Try increasing the total feed and dosing air, then readjust the ratio of the airs to each other. Also, make sure the powder feed hose isn't narrowed due to movement; consider using a hose with a thicker wall to prevent this. Fluctuations in compressed air can also cause sputtering; install compressed air storage directly in front of high consumption system components.
Why is there dust buildup on my WAGNER Sprint 60 L XE?
If you notice dust buildup above the drum or powder tank of your WAGNER Paint Sprayer, it's likely due to too much fluid air. Reduce the fluid air at the throttle to resolve this. Also, check that the throttle is correctly connected to the fluid air connection of the control unit; if not, connect it and readjust the fluid air volume.
What causes bad wrap around with WAGNER Sprint 60 L XE?
If you're experiencing bad wrap around or back-spray with your WAGNER Paint Sprayer, it could be due to insufficient grounding. Ensure that all components are well grounded.
Why doesn't the power indicator light up on my WAGNER Sprint 60 L XE?
If the power indicator on your WAGNER Paint Sprayer doesn't light up, start by ensuring the mains are turned on. Next, check the 2 AT fuses and replace them if they are defective. If these steps don't resolve the issue, there may be a problem with the connection cable to the powder spray gun or grounding. In this case, it is recommended to contact the WAGNER service department or qualified personnel for assistance.
What to do if the feed unit doesn't sink into the powder in my WAGNER Sprint 60 L XE Paint Sprayer?
If the feed unit of your WAGNER Paint Sprayer isn't sinking into the powder, it might be because the guide of the feed unit holder is jammed. Ensure the guide can move smoothly.
General| Brand | WAGNER |
|---|---|
| Model | Sprint 60 L XE |
| Category | Paint Sprayer |
| Language | English |
Highlights dangers to users and device, and measures for hazard avoidance.
Defines terms used in the manual for clarity and consistent understanding.
Specifies the intended application and industry for the Sprint XE manual system.
Details suitability for explosive areas and requirements for electrical devices.
Provides explosion protection markings for the trolley and control unit.
Details information found on the device's identification plates.
Essential safety guidelines for individuals operating the equipment.
Ensures a safe working area, covering dust hazards, PPE, and ignition sources.
Safety guidelines for personnel working with or around the equipment.
Explains the physical construction and functional principles of the system.
Provides detailed technical specifications including dimensions, electrical, and pneumatic data.
Outlines requirements for qualified personnel involved in assembly and commissioning.
Specifies the required environmental conditions for device installation.
Emphasizes the need for qualified and trained personnel for system operation.
Step-by-step guide for powering up the manual powder system and initial checks.
Instructions for setting the fluid air to achieve optimal powder feed.
Defines responsibilities and hazards for personnel performing cleaning and maintenance tasks.
Details essential safety checks, including grounding, to ensure system integrity.
Procedure for safely dismantling the system, emphasizing safety precautions.
Guidelines for environmentally responsible disposal of used electrical equipment.
Lists optional accessories that enhance system functionality.
Describes the switchbox for alternating between Corona and Tribo guns.
Instructions on how to order the correct spare parts, including required information.
Comprehensive list of spare parts for the Airfluid XE manual system.
Notes on manufacturer liability, product origin, and third-party accessories.
Details the warranty coverage, conditions, and procedures for claims.
Official declaration of the trolley's compliance with EU directives and standards.
To Next Page