WAREMA Wisotronic User Manual (English)

Other manuals for WAREMA Wisotronic

Questions and Answers:

E
Edwin ColonAug 31, 2025
Why aren't the comfort functions working as expected on my WAREMA Control Systems?
- D
  Dr. Christopher Cannon MDAug 31, 2025
  If the comfort functions for dawn/dusk, sun, and temperature control are not functioning as desired on your WAREMA Control Systems, first check if the control timer is switched off. If so, switch on the control timer or change the programming. Alternatively, the control timer might not be correctly programmed, so change the programming of the control timer.
P
Peter SmithAug 30, 2025
What to do if the ice alarm is not triggered on my WAREMA Wisotronic?
- N
  Natalie IrwinAug 30, 2025
  If the ice alarm on your WAREMA Control Systems is not triggered, first ensure that ice monitoring is switched on. Next, check if the temperature limit value is set too low and change the limit value, noting the safety instructions. Also, verify that the sensor is properly connected, not faulty, and clean.
T
Theresa ChristensenAug 29, 2025
Why isn't my WAREMA Wisotronic Control Systems precipitation alarm triggering?
- Y
  ybishopAug 30, 2025
  If the precipitation alarm is not triggered on your WAREMA Control Systems, first check if the sensor is connected, faulty, or dirty; clean or check the sensor as needed. Also, ensure that precipitation monitoring is switched on.
N
Nicholas ClarkeAug 29, 2025
What to do if no wind alarm is triggered during a strong wind with my WAREMA Wisotronic Control Systems?
- M
  Mr. Scott BaxterAug 29, 2025
  If no wind alarm is triggered even in a strong wind with your WAREMA Control Systems, the wind speed limit might be set too high. Decrease the wind limit value, while observing safety instructions. Alternatively, wind monitoring might be switched off, so switch on wind monitoring.
A
ashleytorresAug 28, 2025
How to stop a WAREMA Wisotronic wind alarm from triggering in a gentle wind?
- K
  Keith RobinsonAug 28, 2025
  If a wind alarm is triggered even in a gentle wind with your WAREMA Control Systems, the wind speed limit might be set too low. Increase the wind limit value, while observing safety instructions.
S
Shaun DuffyAug 27, 2025
Why isn't my WAREMA Wisotronic Control Systems sun shading system moving at dawn/dusk?
- N
  Nicole RodriguezAug 27, 2025
  If your WAREMA Control Systems sun shading system does not move at dawn/dusk, it could be due to several reasons. First, check if the dawn/dusk control is switched off and switch it on if necessary. Second, ensure that the limit values of the dawn/dusk control are correctly programmed and change them if needed. Finally, verify that the sensor is installed correctly and check its location.
E
Eric NguyenAug 27, 2025
What to do if my WAREMA Wisotronic sun shading system does not move with the sunlight level?
- K
  Kimberly YoungAug 27, 2025
  If your WAREMA Control Systems sun shading system does not move with the sunlight level, it might be because the sun control is switched off. Switch on the sun control.
M
melissa94Aug 26, 2025
What to do if control functions do not respond on my WAREMA Wisotronic Control Systems?
- S
  Shaun GarciaAug 27, 2025
  If the control functions of your WAREMA Control Systems do not respond, first check if the control functions are deactivated on the control panel. If so, activate control functions in the main menu and in the comfort functions. Another reason may be that a safety function is active.
K
Kelly McdanielAug 25, 2025
Why does my WAREMA Wisotronic Control Systems respond sporadically to the EWFS Hand-held transmitter?
- H
  Holly YuAug 26, 2025
  If the WAREMA Wisotronic responds only sporadically to an EWFS Hand-held transmitter, try reducing the distance to the Wisotronic to avoid interfering ambient influences. Also, check for interference from external transmitters such as baby monitors, and switch them off.
K
Kevin AndersonAug 25, 2025
Why doesn't my WAREMA Wisotronic Control Systems respond to the EWFS Hand-held transmitter?
- V
  Valerie MorrisAug 25, 2025
  If the WAREMA Wisotronic does not respond to an EWFS Hand-held transmitter, ensure the transmitter has been learned in. If using an 8-channel EWFS transmitter, verify the correct channel is selected and repeat the move command. Also, ensure the button press isn't too short and repeat the command if needed. Reduce the distance to the Wisotronic to avoid interfering ambient influences. Check for active safety functions due to weather conditions and wait until they subside. If a wind test identified a fault, reset the wind test.