Page 8 ;&(%$*4.8"4,7%<'*#$"&8#=%/7*,#*%4,77%>?@@@?@AA?BCDC1 Item 57342
EF;6GH IJ6KFGLIM NFLMG6MFMO6E6GPJ
E/*4"2"4,$"&8#
Electrical Rating 120VAC / 60Hz / 15A
Rated No Load Speed 4250/min
Cutting Capacity at 0° 3-3/16"
Cutting Capacity at 45° 2-3/16"
Maximum Bevel 45°
Maximum Miter 90°
Saw Blade (sold separately) 10" (254mm) Diameter, 7/64" Wide
5/8" Diamond Arbor
E*$'/%?%S*2&(*%P#*-
%K*,9%$.*%6MGLK6%LNJIKGFMG%EF;6GH%LM;IKNFGLIM%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*Z$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
GI%JK6!6MG%E6KLIPE%LMkPKH%;KIN%FOOLU6MGFT%IJ6KFGLIM-%
G'(8%$.*%J&)*(%E)"$4.%&2%$.*%$&&7%&22%,89%'8/7'3%$.*%$&&7%2(&5%"$#%*7*4$("4,7%&'$7*$%+*2&(*%/*(2&(5"83%,8V%
/(&4*9'(*%"8%$."#%#*4$"&81
M&$*- For additional information regarding the parts listed in the
following pages, refer to Parts List and Diagram on page 20.
N&'8$"83
M&$*- Table Saw MUST be mounted
onto a surface for proper use.
L2%5&'8$"83%&8$&%,%5*$,7%$,+7*%#$,89-
1. Select a table stand which will support
the weight of the Table Saw. Follow the
table saw stand instructions for assembly.
Tighten all connections, making sure the
assembled table is secure and balanced.
2. Mount the Table Saw to the top of the assembled
stand using four 3/8″ bolts, eight 3/8″ washers
and four 3/8″ nuts (not included).
L2%5&'8$"83%&8$&%,%+*84.%&(%&$.*(%)&&9*8%#'(2,4*-
1. Select four 3/8″ bolts, eight 3/8″ washers, and
four 3/8″ nuts* (not included).
*Screws and washers may be used instead, if desired.
2. Place the Table Saw where it will be mounted.
Make a mark in the center of each of the
4 mounting holes. Set the Saw aside.
QFKMLMRl%%GI%JK6!6MG%E6KLIPE%LMkPKH-
Before drilling the holes, make sure that there
are no electric wires, cables, utility lines or
other obstructions in the area to be drilled.
3. Drill the holes straight down, large enough
to allow your mounting hardware to fit.
4. Put the Table Saw in place and mount
using the hardware mentioned above.
Tighten all hardware securely before use1
J&)*(%E'//7V%K*<'"(*5*8$#
1. Connect to grounded 120VAC, 20A receptacle.
To Next Page
Loading...